AD8628ARTZ
Product Specifications
AD8628ARTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8628ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8628ARTZ: zero drift single amplifier with a 1 microvolt offset in SOT-23-5
The AD8628ARTZ is the single channel member of the AD8628/AD8629/AD8630 auto-zero family in a 5-lead SOT-23 body. A 1 uV typical offset and 0.002 uV/C drift mean a thermocouple or strain gauge channel needs no trimpot and no factory zero, and the 2.5 MHz gain bandwidth keeps the channel fast enough for a 1 kSPS scanner.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 1 uV typical, 5 uV maximum |
| Offset voltage drift | 0.002 uV/C typical, 0.02 uV/C maximum, -40 to +125 C |
| Input bias current | 100 pA maximum |
| Input offset current | 50 pA typical, 200 pA maximum |
| Supply current per amplifier | 0.85 mA typical, 1.1 mA maximum at 5 V |
| Gain bandwidth | 2.5 MHz at 5 V, 2 MHz at 2.7 V |
| Slew rate | 1.0 V/us |
| Voltage noise density | 22 nV/root Hz at 1 kHz, 0.5 uV p-p over 0.1 to 10 Hz |
| CMRR | 120 dB typical, 140 dB maximum at 5 V |
| Large signal gain | 125 dB minimum at 5 V |
| Overload recovery | 50 us |
| Output swing | 4.99 V minimum high into 100 k, 1 mV typical low |
| Short circuit current | 25 mA typical, 50 mA maximum |
| Package | 5-lead SOT-23 (RJ-5) |
One microvolt against a thermocouple
A type K thermocouple at 25 C produces about 41 uV per degree C, so 5 uV of maximum offset is 0.12 C of error before the cold junction is considered, and 0.02 uV/C of drift is 3.3 uV, or 0.08 C, across the full 165 C range. That is the entire reason the part exists: the amplifier stops being the error term and the thermocouple and the reference become the ones that matter.
The 100 pA maximum bias current into a 1 kOhm loop resistance is 0.1 uV, which is a fifth of the offset. Into a 100 kOhm source it would be 10 uV, twice the offset, so the source impedance is still the thing to keep low even on an auto-zero part.
Auto-zero noise, stated plainly
An auto-zero amplifier moves its own offset to a chopping frequency, and the usual worry is that the correction adds noise at the switching rate. Here the 0.1 Hz to 10 Hz figure is 0.5 uV p-p and the spot noise is 22 nV/root Hz; integrating the spot figure across 10 Hz gives 70 nV rms, which at a 6.6 peak factor is 0.46 uV p-p. The two agree, so there is no extra low frequency term to budget for.
The 2.5 MHz gain bandwidth at a gain of 100 leaves 25 kHz of closed loop bandwidth, which is a 40 us time constant. A scanner running at 1 kSPS per channel therefore settles, and one running at 100 kSPS does not. The 50 us overload recovery is the other limit: a channel that is driven off scale takes 50 us to come back, which is 5 percent of a 1 ms slot.
Where the current goes
1.1 mA maximum for one channel is 9.6 mAh over a year, which is more than a coin cell can carry and fine for a 4 mA loop. On a battery product the AD8628 is the wrong part on current and the right part on offset, so the choice is between a 1 mA auto-zero channel and a 100 uA chopped channel with a larger offset. State the offset the product needs in microvolts, not in bits, before choosing.
For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, the obsolete part cross reference hub is the check list before a substitute goes in, and medical device components is how a gap is covered without a new line item.
Two questions buyers ask
Why is the SOT-23 version more expensive than the SOIC? The AD8628ARTZ is the 5-lead SOT-23 body and the AD8628ARZ is the 8-lead SOIC. The die is the same and the electrical limits are the same, so the price difference is package and reel economics, and a board that has the room can take the SOIC for less.
Does it need an external capacitor? No. The auto-zero loop is internal and the data sheet states no external component is required, which is one reason the part is used in sealed sensor heads where a film capacitor would drift.