Contact Us

AD8542ARZ

Brand: Analog Devices
Analog Devices AD8542ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8542ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8542ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8542ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8542ARZ: dual general purpose rail-to-rail amplifier in SOIC-8

The AD8542ARZ is the 8-lead SOIC_N version of the 45 uA dual CMOS amplifier, the package that most existing boards already have a footprint for. It offers rail-to-rail input and output, 1 MHz of bandwidth and a 6 mV maximum offset for 90 uA total, which makes it the usual second source for a general purpose dual in through-hole era boards that have been reflowed onto surface mount.

Published values

ParameterValue
Offset voltage1 mV typical, 6 mV maximum per amplifier
Offset voltage drift4 uV/C typical
Input bias current4 pA typical, 60 pA maximum
Supply current, both channels90 uA typical, 130 uA maximum at 5 V
Gain bandwidth1 MHz at 5 V supply
Slew rate0.45 V/us typical, 0.92 V/us at 5 V
Voltage noise density42 nV/root Hz at 1 kHz
Output swing at 1 mA4.9 V minimum high, 25 mV typical low at 5 V supply
Thermal resistance, SOIC-8120 C/W junction to ambient
Phase margin67 degrees
Settling to 0.1%6 us on a 1 V step
Supply range2.7 V to 5.5 V single supply

The second source check that matters

A socket that currently holds a general purpose dual from another vendor will usually accept this part electrically, but three numbers decide whether the board behaves: the input common mode range, the output swing at the load current actually used, and the phase margin with the load capacitance already on the board. This part reaches both rails at the input, swings to 4.9 V and 25 mV at 1 mA, and holds 67 degrees of margin unloaded. A part whose input stops 1.5 V below the positive rail will read a clipped signal in the same socket even though the pins match.

The fourth number is the offset. Six millivolts maximum is fine for a threshold or a filter and wrong for a DC measurement, and no amount of pin compatibility changes that.

What 1 MHz means for the filter it sits in

A Sallen-Key low pass built around this part is limited by the amplifier to roughly a tenth of its gain bandwidth for a clean response, so 100 kHz is the practical ceiling for a two pole section and 50 kHz if the Q is above one. Above that the filter peak moves and the stopband slope flattens, which shows up as a response that no longer matches the simulation.

Supply and decoupling

The part works from 2.7 V to 5.5 V, so the same board can run from a 3.3 V rail or a 5 V rail without a change. Decouple with 100 nF within a few millimetres of the package and take the ground return straight to the plane, because the 4 pA bias current is only an advantage if the board leakage is smaller than it. Flux residue and fingerprint oils on a humid day are several orders of magnitude larger than 60 pA.

Where it is not the right part

Two cases. A precision DC channel needs an offset in the tens of microvolts, which this family does not offer at any grade. A channel that has to settle fast needs more than 0.92 V/us, and the 8 MHz and 10 MHz families listed on the cross reference page cost only a few hundred microamps more per amplifier.

Buyers usually arrive at the obsolete part cross reference hub to find the family alternatives, then use the amplifier cross reference to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.

Two questions buyers ask

Does the AD8542ARZ work on a 5 V rail with a 2 kOhm load? Yes, with a reduced swing. The published output figures are taken at 1 mA, so at 2.5 mA the high swing drops by roughly 100 mV and the low swing rises, which is worth checking against the ADC input range.

What is the maximum supply current for the pair? 130 uA at 5 V over temperature, against 90 uA typical at 25 C.