Contact Us

AD8479ARZ

Brand: Analog Devices
Analog Devices AD8479ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8479ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8479ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8479ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8479ARZ: a difference amplifier that sits 600 volts above its own supply

The AD8479ARZ measures a differential voltage while both inputs sit anywhere within plus or minus 600 V of the part's own ground, on a supply as low as plus or minus 2.5 V. Gain is fixed at 1, output is rail-to-rail, the differential input range is plus or minus 14.7 V, bandwidth is 310 kHz and supply current is 550 microamps typical. Two 1 megohm resistors in front of the input stage are what makes the common mode range possible, and they are also where most of the noise and the gain error come from.

Published values

ParameterValue
Common mode rangeplus or minus 600 V, independent of the supply
Differential input rangeplus or minus 14.7 V
Gain1, fixed; 0.01 percent gain error on the A grade, 0.005 on the B
Gain nonlinearity10 ppm maximum on A, 5 on B
Gain drift5 ppm per degree maximum
Offset voltage3 mV maximum on A, 1 mV on B
Offset drift15 microvolts per degree maximum on A, 10 on B
CMRR90 dB minimum on A, 96 on B, at a 600 V common mode
Bandwidth310 kHz
Noise1.6 microvolts per root hertz from 100 Hz to 100 kHz
Supply rangeplus or minus 2.5 V to plus or minus 18 V
Supply current550 microamps typical
PSRR84 dB minimum on A, 90 on B
Package8-lead SOIC

Six hundred volts of common mode, and what it costs

The input divider is two 1 megohm resistors, and their thermal noise is 129 microvolts per root hertz each, which appears as 1.6 microvolts per root hertz at the output once the divider ratio and the differential sensing are accounted for. Over the full 310 kHz band that is about 0.9 mV RMS, which is the same order as the 3 mV offset and much larger than any signal below a millivolt.

That is the honest trade on this part. It is a high side current sense and battery monitor, not a precision bridge front end, and the numbers say so. A 100 mV shunt signal with 0.9 mV of RMS noise gives a signal to noise ratio of 41 dB, about 6.5 effective bits, which is enough for a protection threshold and not enough for a fuel gauge that reads to one percent.

Where the offset and the gain error sit in a current sense chain

Three millivolts of input offset on a 100 mV full scale shunt is 3 percent of the reading, and it does not go away with a bigger shunt because the differential range stops at plus or minus 14.7 V. The B grade at 1 mV is 1 percent. A shunt amplifier with a chopper input would do better, but it could not sit at a 600 V common mode, which is the whole reason this part exists.

The gain error of 0.01 percent is trimmed at the factory and holds to 5 ppm per degree, so over a 100 degree swing it adds 500 ppm, which is 0.05 percent. Compared with the 3 percent offset term it is negligible, and compared with a 0.5 percent shunt resistor it is negligible twice over. The shunt, not the amplifier, sets the current accuracy in most current sense channels.

Two rails and a ground that is not the measurement ground

The part runs from plus or minus 2.5 V to plus or minus 18 V, and the input common mode is measured against its own reference pins rather than against the supply. That is what allows a 48 V or 400 V rail to be monitored by a device running from a 5 V supply, with the reference pins tied to the local ground.

One consequence is worth stating: the 600 V is a common mode rating, not an isolation rating. There is no barrier inside the package, so a fault that takes the input beyond the rating puts the low voltage side at risk. Where the measurement has to be safe rather than merely wide, an isolated amplifier or a module with a barrier is the right part.

Sourcing notes for this family: the amplifier cross reference holds the cross references, medical device components is the pre substitution check, and how to verify a drop in replacement is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask about the high voltage difference amplifier

Can it measure a negative rail as well as a positive one? Yes. The common mode range is symmetric at plus or minus 600 V, so a negative supply rail is measured the same way as a positive one, with the sign set by which input carries the higher voltage.

Is the 600 V rating a working voltage or a withstand rating? It is the continuous common mode range of the input divider. The package provides no galvanic isolation, so it is not a safety barrier rating.