Contact Us

AD8476BRMZ

Brand: Analog Devices
Analog Devices AD8476BRMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8476BRMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8476BRMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8476BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8476BRMZ: 330 microamps of differential ADC driver

The AD8476BRMZ is the B grade of a unity gain fully differential amplifier intended to sit between a single ended source and a differential converter. It draws 330 microamps, has a fixed gain of 1, drives switched capacitor inputs with rail-to-rail outputs, and puts a VOCM pin on the package to set the output common mode independently of the input. Harmonic distortion is -126 dBc second and -128 dBc third at 10 kHz, output noise is 39 nV per root hertz, and the supply spans 3 V to 18 V single or plus or minus 1.5 V to plus or minus 9 V.

Published values

ParameterValue
Supply current330 microamps
Supply range3 V to 18 V single, plus or minus 1.5 V to plus or minus 9 V dual
Gain1, fixed by internal resistors
Gain drift1 ppm per degree maximum
Gain error0.02 percent for the B grade, 0.04 for the A grade
Bandwidth6 MHz small signal at 200 mV, 1 MHz large signal at 2 V peak to peak
Slew rate10 V per microsecond
Settling1 microsecond to 0.01 percent on a 2 V step
Distortion-126 dBc second harmonic, -128 dBc third at 10 kHz
Noise39 nV per root hertz at 10 kHz, 6 microvolts peak to peak from 0.1 to 10 Hz
Differential offset50 microvolts maximum for B, 200 for A; 900 over temperature
Offset drift1 microvolt per degree typical, 4 maximum
CMRR90 dB for B, 80 dB for A
Overload18 V beyond either supply without damage
Package8-lead MSOP

Six megahertz small signal against one megahertz large signal

The difference between the two bandwidths is not a measurement quirk. At 200 mV peak to peak the internal amplifier stays in its linear region and the -3 dB point is 6 MHz; at 2 V the slew rate of 10 V per microsecond limits a full swing sine to about 800 kHz, and the specified large signal figure is 1 MHz. A driver chosen on the 6 MHz number for a 2 V signal will be 6 dB down where the datasheet promised flat response.

For a 16-bit converter sampling at 250 kSPS the signal band is under 125 kHz, so both numbers are comfortable and the settling figure is what matters. One microsecond to 0.01 percent on a 2 V step is 200 microvolts of residual, which is 5 LSB at 16 bits, so the converter needs the full acquisition window and not less.

The resistors are inside, and that is the whole point

Four 10 kohm resistors set the gain and the common mode conversion, and their matching is what gives 1 ppm per degree of gain drift and 90 dB of CMRR. Building the same function from an op amp and four discrete resistors needs 0.01 percent parts and a matched network, and the drift of that network is usually worse than the amplifier it feeds.

The fixed gain of 1 is the limitation as well as the benefit. A 2.5 V single ended signal does not fit a 5 V differential input without attenuation, and this part cannot attenuate. Where the source is larger than the converter's range, a resistor divider in front adds its own mismatch and gives back the CMRR the internal network just bought.

Three hundred and thirty microamps and eighteen volts of abuse

The input survives 18 V beyond either supply, which on a plus or minus 5 V rail means a plus or minus 23 V fault. In a battery powered instrument where a probe can be connected to a live node, that is the specification that keeps the converter behind it alive.

The output common mode is set by VOCM and follows it with 0.05 percent of gain error, so a converter reference of 2.5 V can set the output midscale directly. Driving VOCM from a resistive divider is acceptable because the pin draws almost no current, but the divider's noise appears at the output multiplied by the common mode gain, which is one, so a bypass capacitor at the pin is normally part of the circuit.

The pages that answer this most often are the ADC and DAC cross reference for the family alternatives, the amplifier cross reference for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.

Two questions buyers ask about the ADC driver

Can it convert single ended to differential? Yes, one input can be driven and the other returned to a fixed voltage through the same impedance, and the output is differential. The datasheet covers both single ended and differential drive.

What is the difference between the A and B grades? The B grade halves the differential offset from 200 to 50 microvolts and raises the CMRR from 80 to 90 dB. Gain drift, noise and bandwidth are the same on both.