Contact Us

AD8342ACPZ

Brand: Analog Devices
Analog Devices AD8342ACPZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8342ACPZ — Analog & Mixed-Signal ICs | Superb Automation

AD8342ACPZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8342ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8342ACPZ: 22.7 dBm of Input IP3 at 98 mA Is a Receiver Budget Decision

The AD8342 is an active receive mixer covering low frequency to 3.8 GHz with a differential high impedance RF port, a single ended 50 ohm local oscillator port and an open collector differential intermediate frequency output. Conversion gain is 3.7 dB, noise figure 12.2 dB, input third order intercept 22.7 dBm and input 1 dB compression 8.3 dBm at a local oscillator drive of 0 dBm, on a single 5 V supply drawing 98 mA. Those five numbers together describe a block that trades noise figure for linearity, and the trade is what has to be checked against the receiver behind it rather than against a data sheet headline.

Where the intercept figure sits

An input intercept of 22.7 dBm means that two tones of -10 dBm each produce third order products at roughly -10 plus twice the difference between the intercept and the tone level, that is about -55 dBc, or -65 dBm each. With a 12.2 dB noise figure and a 3.7 dB conversion gain, the input referred noise in a 1 Hz band is about -161.8 dBm, so a two tone test at -10 dBm is 150 dB above the noise floor and the mixer is being asked a question about blocking rather than about sensitivity. In a receiver that also has to hear a -100 dBm signal, the same mixer is operating 90 dB below the two tone level, so the linearity margin is bought with a noise figure that the front end amplifier has to recover.

The open collector output and its load

The intermediate frequency output is an open collector differential pair without internal load resistors, so the conversion gain of 3.7 dB is only meaningful with the load that the data sheet specifies. A differential filter or a differential amplifier such as the parts named in the data sheet forms the load, and the output must be pulled to the positive rail through that network. Anyone who measures a board with the output unterminated will see a different gain and a different compression point, and neither of those is a part defect.

ParameterValueWhat it decides
Frequency rangeLow frequency to 3.8 GHzCovers cellular, ISM and instrumentation bands
Conversion gain3.7 dBOnly valid with the specified output load
Noise figure12.2 dBInput referred noise near -161.8 dBm per hertz
Input IP322.7 dBmTwo tones at -10 dBm give products near -65 dBm
Input P1dB8.3 dBmUpper limit for a single wanted carrier
Local oscillator drive0 dBmSets the drive amplifier and its isolation
Local oscillator port50 ohm single endedA balun is inside the part, not on the board
RF portDifferential, high impedanceNeeds a balun or a differential front end filter
Intermediate frequency portOpen collector differentialExternal pull ups and a differential load
Supply5 V at 98 mA0.49 W, half of it in the output stage
Power-downPin controlledA receive only slot can be switched off
Package3 mm by 3 mm LFCSP with padThe pad is the only thermal path for 0.49 W

Local oscillator drive and leakage

The local oscillator port expects 0 dBm into 50 ohm, which is 0.63 V peak to peak, and it is single ended, so the balun and the matching are inside the package. A drive level well above 0 dBm changes the conversion gain and the intercept, and a level well below it raises the noise figure faster than the intercept falls, so the drive should be set with a power meter rather than with the synthesizer's setpoint. The differential radio frequency port is high impedance, which allows a differential filter to be placed directly at the input without a transformer, but it also means the port cannot be treated as a 50 ohm load for a single ended filter.

Supply decoupling and the exposed pad

At 98 mA from 5 V the part dissipates nearly half a watt, and in a 3 mm by 3 mm body the exposed pad and its via array carry that heat. The supply pins need decoupling close to the package because the output stage current is modulated at the intermediate frequency, and any shared impedance between the radio frequency and intermediate frequency return paths converts that current into feedback. A split ground with a single connection under the pad is the arrangement the evaluation board uses.

Procurement notes for a mixer of this class

The order code carries the package, and the figures above belong to the part rather than to a grade, so a substitute has to be compared on conversion gain, noise figure and intercept together. A mixer with a higher intercept and a higher noise figure is not a drop in part for a receiver that is already noise limited. Current availability for this family is tracked through RF component sourcing, and the wider question of consolidating a radio bill of materials is covered in BOM consolidation. Where the part is being replaced because of a lead time, the comparison checklist is in component lead time solutions.