AD823ARZ
Product Specifications
AD823ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD823ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD823ARZ: 16 MHz From 2.6 mA per Amplifier on a Single 3 V Rail
The AD823ARZ is a dual FET input amplifier with 16 MHz of minus 3 dB bandwidth at unity gain into a 100 kohm load, and it reaches that bandwidth while drawing 2.6 mA per amplifier. The supply range is 3.0 V to 36 V single, or the equivalent dual supplies, which puts it in the small group of parts that keep their ac performance on a 3 V rail. Settling to 0.01 percent on a 2 V step takes 350 ns, input bias current is 25 pA maximum, and the worst harmonic at 20 kHz is minus 108 dBc. The output drives 15 mA while staying within 0.5 V of either supply, and the input range extends below ground with no phase inversion when the input reaches the rails.
Published values
| Parameter | Value |
|---|---|
| Configuration | Dual FET input |
| Bandwidth | 16 MHz at minus 3 dB, gain of plus one, 100 kohm load |
| Settling time | 350 ns to 0.01 percent, 2 V step |
| Supply current | 2.6 mA per amplifier |
| Supply range | Single 3.0 V to 36 V |
| Input bias current | 25 pA maximum |
| Distortion | Minus 108 dBc worst harmonic at 20 kHz |
| Output current | 15 mA, 0.5 V from either supply |
| Output swing | Rail to rail |
| Bodies | 8-lead PDIP and SOIC |
What 16 MHz buys in a 12 to 16 bit channel
The bandwidth number is only useful in combination with the settling figure, because a converter acquisition window is a settling problem rather than a bandwidth problem. At 350 ns to 0.01 percent on a 2 V step the part settles to better than the resolution of a 14 bit converter within a fraction of a microsecond, which is why it appears in front of 12 bit to 16 bit data acquisition channels. The 20 kHz distortion figure then decides whether the channel is clean enough for an audio band measurement, because a buffer that settles fast but distorts at 20 kHz puts its own signature into the reading and the calibration cannot remove it.
The 3 V rail and why it changes the input network
On a 3 V single supply the input common mode barely fits a ground referenced sensor, and the fact that the input range extends below ground is what allows a sensor return that is not exactly at the local ground. Output swing to within 0.5 V of either rail at 15 mA means the usable span at the converter is about 2 V, so the amplifier gain has to be chosen against that span rather than against the supply. A board that was scaled for a 5 V rail and then moved to 3 V without changing the gain will clip the top of the input range, and the symptom is a reading that stops changing at a value that looks like a sensor limit rather than an amplifier limit.
Pin compatible bodies and the DIP question
The SOIC and the PDIP share a pinout, so a board can move between them without a topology change, but only the SOIC is normally available in volume once the DIP is phased out. Both bodies are specified over the industrial range. The dual package also means that one amplifier can buffer the converter while the second one drives a filter, and the shared supply pins keep the board simple, at the cost of supply coupling between the two halves that has to be handled with local decoupling at each package pin rather than at the board edge.
Supply headroom and power at 36 V
Running the same part at 36 V is possible and it is the reason the device shows up in industrial front ends, but the dissipation changes by an order of magnitude compared with a 3 V rail. At 2.6 mA per amplifier and a 36 V supply each half dissipates about 94 mW before any load current, so an 8-lead package with two amplifiers sits near 190 mW and the thermal resistance of the SOIC becomes the deciding factor for the ambient limit. Derating the supply to 24 V or 15 V where the signal span allows it is the usual answer. The amplifier cross reference page groups the dual FET input parts by supply range and bandwidth, the pin to pin cross reference page lists what swaps without a board change, and the obsolete part cross reference hub covers the case where the exact grade has already been discontinued.