AD8237ARMZ
Product Specifications
AD8237ARMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8237ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8237ARMZ: Zero-Drift, True Rail-to-Rail, 115 Microamps
The AD8237ARMZ is a micropower zero-drift instrumentation amplifier with a true rail-to-rail input and output, 115 microamps of supply current, a supply range of 1.8 V to 5.5 V, and a gain set by two external resistors as 1 plus R2 divided by R1. Its DC specifications are unusual for the current class: 106 dB minimum common-mode rejection, 0.3 microvolts per degree Celsius maximum offset drift, 0.005 percent maximum gain error at all gains and 0.5 parts per million per degree maximum gain drift, with 1 nA of input bias current guaranteed to 125 degrees. On-chip radio frequency filtering and an 8 kV human body model ESD rating complete the picture.
Published values
| Parameter | Value |
|---|---|
| Supply current | 115 microamps |
| Supply range | 1.8 V to 5.5 V |
| Gain | 1 plus R2 divided by R1, two external resistors |
| Common-mode rejection | 106 dB minimum |
| Offset drift | 0.3 microvolts per degree Celsius maximum |
| Gain error | 0.005 percent maximum at all gains |
| Gain drift | 0.5 parts per million per degree Celsius maximum |
| Input bias current | 1 nA guaranteed to 125 degrees Celsius |
| Input and output | True rail to rail, no crossover distortion |
| Bandwidth control | BW pin sets the compensation |
| ESD | 8 kV human body model |
| Package | 8-lead MSOP |
Two resistors instead of one, and why the gain drift is so low
Setting gain with a ratio rather than with a single resistor against an internal value removes the internal resistor's drift from the gain equation entirely: the gain depends only on the ratio R2 divided by R1, and two resistors on the same substrate in the same package track to within a few parts per million per degree. That is how the part reaches 0.5 parts per million per degree when a circuit with one resistor reaches 5 to 25. The cost is one more component and the requirement that both resistors be the same type and, ideally, in the same network. Using a discrete pair with different temperature coefficients throws the advantage away.
The BW pin is a noise and stability control
The bandwidth pin adjusts the internal compensation, trading bandwidth for stability with capacitive loads and for lower noise at low frequency. Running it at the widest setting gives the fastest response and the most output noise; narrowing it filters the chopper ripple and makes the part easier to drive into a converter. For a bridge sampled at 10 Hz, the narrow setting is the right choice and the extra bandwidth buys nothing. For a current sense in a motor loop, the wide setting is needed and the ripple has to be filtered externally.
Rail to rail on 1.8 V, with a picoamp class of input
At 1.8 V the input range covers the full supply, which is what allows a single cell instrument to measure a signal that sits at either rail. The input bias current of 1 nA is higher than a JFET part, so a source above 1 Mohm will develop millivolts of offset; for those, a JFET input amplifier is still the answer. Below 100 kohm the bias current is negligible and the zero-drift performance dominates. The on-chip radio frequency filter matters in a portable device with an antenna nearby, since an instrumentation amplifier with a long input trace rectifies radio frequency energy into an offset that looks like drift.
Availability and second sourcing
Zero drift, a two resistor gain and a true rail-to-rail input are three properties that rarely appear together, so a substitute usually gives up one of them; the gain structure is the one to check first, because a single resistor part will not produce the same gain for the same components. The amplifier cross reference page groups the zero-drift amplifiers by gain structure, the ADI part second source page separates the grades that match on drift, and the lead time page shows availability.