AD822ARZ-REEL7
Product Specifications
AD822ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD822ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD822ARZ-REEL7: a dual FET input amplifier that runs from a single 5 V to 30 V supply
What this order code is
AD822ARZ-REEL7 is a dual precision FET input operational amplifier that operates from a single supply of 5 V to 30 V or from dual supplies of plus and minus 2.5 V to plus and minus 15 V. It has true single supply capability, which in this part means the input common mode range extends below the negative rail, so a signal that goes below ground can be amplified without a second supply. The output swings to within 10 mV of each rail and drives 15 mA minimum into a load and 350 pF of capacitance at unity gain.
The dc specifications are a 800 microvolt maximum offset, a 2 microvolt per degree C drift and an input bias current below 25 pA, which is what a FET input buys at source impedances in the gigaohm range. The ac specifications are 1.8 MHz of unity gain bandwidth, 3 V per microsecond of slew rate and minus 93 dB of total harmonic distortion at 10 kHz, on 800 microamps per amplifier. The EP version of the same part is screened for defence and aerospace use over minus 55 C to plus 125 C.
Parameters as published
| Item | Value |
|---|---|
| Amplifier count | two |
| Single supply range | 5 V to 30 V |
| Dual supply range | plus and minus 2.5 V to plus and minus 15 V |
| Input range | extends below the negative rail |
| Output swing | within 10 mV of each rail |
| Input offset voltage | 800 microvolts maximum |
| Offset drift | 2 microvolts per degree C |
| Input bias current | under 25 pA |
| Unity gain bandwidth | 1.8 MHz |
| Slew rate | 3 V per microsecond |
| Distortion | minus 93 dB total harmonic at 10 kHz |
| Output current | 15 mA minimum |
| Capacitive load | 350 pF at unity gain |
| Supply current | 800 microamps per amplifier |
Numbers that decide the application
The bias current is the number that makes the part interesting and the number that limits it. At 25 pA a 1 Gohm source produces 25 mV of offset, which is 31 times the 800 microvolt offset the amplifier is bought for, so the gigaohm source impedance in the vendor description is the point at which the bias current becomes the dominant error and not a region where the part is still precise. At 10 Mohm the same current gives 250 microvolts, which is a third of the offset and a reasonable place to stop.
The single supply range of 5 V to 30 V with an input that goes below the negative rail is the practical feature. A photodiode preamp or a shunt monitor can sit on a 12 V rail and accept a signal that swings a few hundred millivolts below ground without a negative supply, and the output still reaches within 10 mV of both rails. Drift of 2 microvolts per degree C over a 100 degree swing is 200 microvolts, a quarter of the offset, so a channel that is trimmed at room temperature stays within about 1 mV over the industrial range before the bias term.
The 350 pF capacitive load rating at unity gain is generous for a FET input amplifier and is what allows the part to drive a cable or a large area detector directly. Above that capacitance the output impedance and the load form a pole inside the loop and the stage needs a series resistor, which costs bandwidth but keeps the loop stable. The 15 mA minimum output current is enough for a 600 ohm load at 9 V peak to peak with margin.
Where it fits and where it does not
It fits photodiode and photomultiplier preamps, active filters, 12 to 14 bit data acquisition front ends, medical instrumentation and battery powered precision instruments that run from a single rail. It does not fit a 3.3 V only system, a signal path above a few hundred kilohertz, or a channel that needs better than 800 microvolts of offset without a trim. It is also not a rail to rail input part, so a follower at the positive rail is outside the common mode range even though the output can reach that rail.
Supply and second source questions
The questions we get are about the supply range, the input range below ground and the bias current at temperature, since the 25 pA figure is a room temperature number and it rises with temperature in every FET input amplifier. A substitute that matches the pinout but has a bipolar input will not hold the bias current at a gigaohm source, and that difference does not appear in a distributor filter. The FET input parts we hold are listed on the amplifier cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check the body, the grade and the packing, and we ask for the source impedance on the line because that is what decides whether this part or a lower bias device is the right one. The EP version is a separate route with a controlled baseline, and we will not present the commercial part as an equivalent for a screened requirement. Send the line items, quantities and required date through the BOM shortage recovery page, and for defence and aerospace programmes the defence grade components page describes how the screened parts are handled.
Request Quote — In Stock, 100% New & Original, Full Warranty