AD8223ARMZ-R7
Product Specifications
AD8223ARMZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8223ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8223ARMZ-R7: A Single Supply Instrumentation Amplifier with a Gain of 5 Floor
What this part is
The AD8223 is a single supply instrumentation amplifier that delivers a rail to rail output from a 3 V to 24 V rail, with a gain set by one resistor from 5 to 1,000. With no resistor at all the part sits at a gain of 5, which is the difference between it and the parts whose minimum gain is 1: a channel that never needs unity gain gets the higher minimum as a feature, because the input stage can then be optimised for a smaller input range and a lower noise contribution.
The input common mode range reaches 150 mV below the negative rail, so a shunt or a thermocouple sitting at ground can be amplified on a single supply. Input bias current is 25 nanoamps maximum, input noise is 30 nanovolts per root hertz at 1 kHz, the supply current is 500 microamps maximum, and the part conforms to the 8 lead pin arrangement that instrumentation amplifiers in this class share. It works from plus and minus 2 V to plus and minus 12 V on dual supplies as well, and the body is an 8 lead MSOP in this order code.
Published figures that matter to a buyer
| Gain range | 5 to 1,000, set by one resistor; 5 with no resistor |
| Supply, single | 3 V to 24 V |
| Supply, dual | plus and minus 2 V to plus and minus 12 V |
| Input common mode | to 150 mV below the negative rail |
| Input bias current | 25 nanoamps maximum |
| Input noise | 30 nanovolts per root hertz at 1 kHz |
| Supply current | 500 microamps maximum |
| Output swing | rail to rail |
| Pin arrangement | the 8 lead industry standard for instrumentation amplifiers |
| Body | 8 lead MSOP |
Where the headline numbers stop
The gain resistor values are not small. For a gain of 10 the resistor is 40,000 ohm, for 100 it is 2,105 ohm and for 1,000 it is 201 ohm, so the low gain settings need a high value resistor whose tolerance and temperature coefficient are part of the gain error, and the high gain settings need a low value where the resistance of the track begins to matter. A 1 percent resistor at a gain of 10 is a 1 percent gain error: the part is accurate and the resistor is the channel.
Thirty nanovolts per root hertz over a 1 kHz band is 949 nanovolts rms, and the same density over 10 kHz is 3 microvolts rms. Against a 25 nanoamp bias current through a 1 megohm source that is 25 mV of offset, so a high impedance sensor is limited by the bias current rather than by the noise or the gain. A lower source impedance is worth more than a better amplifier in that case.
Five hundred microamps at 24 V is 12 mW, which is the top of the range and the case that matters on a loop powered transmitter: the supply current is a maximum at any voltage, so the dissipation grows with the rail and a 24 V loop has to carry it. At 3 V the same current is 1.5 mW, which is the figure that makes the part usable in a battery instrument.
Applications where it fits
- Low power medical instrumentation with a ground referenced sensor.
- Transducer and bridge interfaces.
- Thermocouple amplifiers on a single supply.
- Industrial process control input cards.
- Loop powered transmitters where the supply current budget is the constraint.
Two questions buyers ask
How does this differ from the AD8226? The 8226 has a gain floor of 1 and a wider supply range with lower noise, and it costs more. The 8223 has a gain floor of 5, a maximum supply current and a price that suits a high channel count. A channel that needs a gain of 1 or 2 cannot use the 8223, and a channel that will never go below 5 usually does not need the 8226.
Is the 150 mV below the rail enough for a shunt in the return leg? It is enough for a small negative excursion, not for a shunt that sits well below ground. The 150 mV is a common mode limit and it is a specification at the stated supply, so a channel that sees a switching return can exceed it on every edge and the part will clip even though the average voltage is inside the range.
Sourcing notes and next step
AD8223ARMZ-R7 is the 8 lead MSOP body on tape and reel. Because the pin arrangement is the industry standard for this class, an incoming board can carry a substitute without a board change, which is exactly the case where a grade or a specification difference goes unnoticed. The amplifier cross reference page sets out the fields to compare, the pin to pin cross reference page covers what must match before a drop in is claimed, and the analog and mixed signal IC family page lists the rest of the amplifier line.
Request Quote — In Stock, 100% New & Original, Full Warranty