AD8221ARMZ-R7
Product Specifications
AD8221ARMZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8221ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8221ARMZ instrumentation amplifier in MSOP: 80 dB of common mode rejection at 10 kHz
The AD8221ARMZ is the 8-lead MSOP member of the AD8221 instrumentation amplifier family. One external resistor sets the gain from 1 to 1000, the common mode rejection stays at 80 dB minimum out to 10 kHz at unity gain, and the input voltage noise is 8 nanovolts per root hertz at 1 kHz. The MSOP body takes half the board area of the SOIC part with the same die and the same specification, so the choice between the two order codes is an assembly question rather than a performance one.
Published values
| Parameter | Value |
|---|---|
| Gain | 1 to 1000, set by one external resistor, G equals 1 plus 49.4 kohm divided by RG |
| Common mode rejection at DC, G equals 1 | 80 dB minimum on the AR grade, 90 dB on the BR grade |
| Common mode rejection at 10 kHz | 80 dB minimum at G equals 1, 90 dB at G equals 10 |
| Input voltage noise | 8 nanovolts per root hertz at 1 kHz, maximum |
| Input bias current | 1.5 nA maximum on the AR grade, 0.4 nA maximum on the BR grade |
| Bandwidth | 825 kHz at a gain of 10 |
| Gain nonlinearity | 15 ppm at a gain of 100 on the AR grade |
| Supply | single or dual, plus and minus 2.3 V to plus and minus 18 V |
| Package | 8-lead MSOP, half the board area of the 8-lead SOIC |
| Application fit | bridge signal conditioning, strain gauges, medical instrumentation, precision data acquisition |
Why rejection at 10 kHz is the number that sells this part
Most instrumentation amplifiers hold their rejection at low frequency and lose it above a few hundred hertz. In a plant with variable frequency drives, the interference that matters sits at the switching frequency and its harmonics, which is exactly where the rejection curve of an ordinary part has already fallen away. A minimum of 80 dB at 10 kHz at unity gain is what keeps a bridge signal clean without a front end filter that would also slow the channel.
The rejection is quoted at a gain of 1, which is the hardest case. At a gain of 10 the minimum is 90 dB, at 100 it is 100 dB, and at 1000 it is 100 dB at 10 kHz. The DC rejection numbers are 80 dB, 100 dB, 120 dB and 130 dB on the AR grade, so the part is a genuine instrument amplifier at high gain and an ordinary difference amplifier at unity.
The gain resistor is the accuracy of the channel
Gain is 1 plus 49.4 kohm divided by RG, so a 49.4 ohm resistor gives a gain of 1000 and a 494 ohm resistor gives 101. The tolerance and the temperature coefficient of that resistor land directly on the gain, and at a gain of 1000 a 0.1 percent resistor is a 0.1 percent gain error before the part contributes anything.
Gain nonlinearity of 15 ppm at a gain of 100 sets the ceiling for a 16-bit channel: 15 ppm is about one least significant bit at 16 bits, so a part used at that gain in a 16-bit system is limited by the amplifier rather than by the converter. At a gain of 1 the nonlinearity is 3 ppm and the converter becomes the limit.
Bias current against source impedance
The AR grade draws 1.5 nA maximum of input bias current, the BR grade 0.4 nA. Into a 10 kohm bridge that is 15 microvolts of offset, which is the same order as the offset of many parts in this class; into a 1 kohm source it is 1.5 microvolts and disappears. The higher grade earns its price when the source is above about 5 kohm or when the channel has to hold its offset over temperature.
The MSOP package is the same die in a smaller body, so the electrical numbers are identical. What changes is the thermal resistance and the assembly: the smaller body heats more per watt and needs the copper under it to be part of the answer, and it takes less space in a multichannel card.
When an order code in this family cannot be found, the amplifier cross reference lists what else does the same job, the ADI second source page covers what to check before a part is dropped into an existing board, and vendor consolidation is the route we take on a live shortage.
Two questions buyers ask
Does the AD8221 need a separate reference buffer? The REF pin sets the output level and is a high impedance node inside the part, so it has to be driven from a low impedance source, either a reference or an amplifier output. A divider alone will move with the load current.
Is the MSOP version a different die from the SOIC version? No. The two order codes are the same amplifier in different bodies, with the same gain equation and the same rejection. The difference is board area, thermal resistance and the assembly line that can place the package.