AD8211YRJZ
Product Specifications
AD8211YRJZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8211YRJZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8211YRJZ: 5-Lead Current Shunt Monitor, Minus 2 V to Plus 65 V
The AD8211YRJZ puts a fixed gain of 20 current shunt amplifier into a 5-lead SOT package. The common-mode input range is minus 2 V to plus 65 V operating and minus 3 V to plus 68 V continuous, the differential input range is 0 mV to 250 mV, and the output is buffered so it can drive a converter input or a filter directly. Typical offset drift is 5 microvolts per degree Celsius, gain drift is minus 13 parts per million per degree, common-mode rejection is 120 dB at DC, and the gain error is 0.35 percent typical over the full temperature range. Human body model ESD rating is 4000 V, and the part is qualified for automotive applications.
Published values
| Parameter | Value |
|---|---|
| Gain | 20 V per V, fixed |
| Common-mode range, operating | minus 2 V to plus 65 V |
| Common-mode range, continuous | minus 3 V to plus 68 V |
| Differential input range | 0 mV to 250 mV |
| Supply | 5 V nominal |
| Offset drift | 5 microvolts per degree Celsius typical |
| Gain drift | minus 13 parts per million per degree Celsius typical |
| Gain error | 0.35 percent typical over temperature |
| Common-mode rejection | 120 dB typical at DC |
| ESD | 4000 V human body model |
| Temperature | minus 40 to plus 125 degrees Celsius |
| Package | 5-lead SOT |
Two hundred and fifty millivolts is the whole input range
The differential input is specified from 0 mV to 250 mV, so the maximum shunt signal before the output saturates is a quarter of a volt. With a gain of 20 that is 5 V at the output, which is the full supply rail, so in practice the usable input is closer to 200 mV once the output headroom is taken. On a 1 mOhm shunt that is 200 A, which is the high current end; on a 10 mOhm shunt it is 20 A. The number to check first is the product of shunt resistance and maximum current: if it exceeds 200 mV, the amplifier will limit before the current does, and the reading at the top of the range will be a flat line that looks like a fault.
Why the supply current rises at low common mode
Below a 5 V common mode the internal bias arrangement draws more supply current, and the datasheet gives the relationship as a straight line so the extra can be budgeted. In a system where the same 5 V rail feeds several of these monitors plus a microcontroller, the sum matters at the low end of the common-mode range, which is exactly the case for a low-side or a near-ground measurement. The output stays valid, but the rail droop moves the reference for every other channel that shares it. Feed the monitors from their own regulator or from a rail with headroom, and keep the decoupling at the pin rather than at the far end of the board.
Buffered output and the filter after it
The output buffer means an RC filter can be added without the resistor appearing as a load error, which is not true of an unbuffered current sense output. A 1 kohm and 100 nF pair gives a 1.6 kHz pole that removes the switching ripple from a motor drive while leaving a 100 microsecond response, fast enough for overcurrent protection. Place the resistor at the amplifier and the capacitor at the converter, so the trace between them is driven by the resistor rather than by the amplifier, and the capacitor's parasitics do not sit on the amplifier output. The buffered output also means the converter's sampling glitch does not feed back into the shunt measurement.
Availability and second sourcing
A 5-lead SOT current sense amplifier is a commodity part with several near equivalents, and the differences that matter are the common-mode range, the differential range and the reference structure: a part without reference pins cannot do bidirectional measurement. The amplifier cross reference page groups them by those three parameters, the pin to pin cross reference page lists the 5-lead footprints that match, and the verification checklist is what to run before a substitute goes into a board.