AD8206YRZ
Product Specifications
AD8206YRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8206YRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8206YRZ: Bidirectional Current Shunt Amplifier, Minus 2 V to Plus 65 V
The AD8206YRZ measures a small differential voltage sitting on top of a large common-mode voltage. It has a fixed gain of 20, an operating input common-mode range of minus 2 V to plus 65 V, a survival range of minus 25 V to plus 75 V, and it runs from a single 5 V supply. Offset drift is 15 microvolts per degree Celsius typical, gain drift is 30 parts per million per degree typical, and common-mode rejection is 80 dB from DC to 20 kHz. The two reference pins set the output offset anywhere from 0.08 V to 4.7 V, which is what makes the part bidirectional: with one reference at the supply and the other at ground the output sits at half scale and the sign of the current is readable.
Published values
| Parameter | Value |
|---|---|
| Gain | 20 V per V, fixed |
| Common-mode range, operating | minus 2 V to plus 65 V |
| Common-mode range, survival | minus 25 V to plus 75 V |
| Supply | 5 V single supply, 12.5 V absolute maximum |
| Offset drift | 15 microvolts per degree Celsius typical |
| Gain drift | 30 parts per million per degree Celsius typical |
| Common-mode rejection | 80 dB from DC to 20 kHz |
| Output offset range | 0.08 V to 4.7 V, set by VREF1 and VREF2 |
| Temperature, Y and WY grades | minus 40 to plus 125 degrees Celsius |
| Temperature, WH grade | minus 40 to plus 150 degrees Celsius |
| Package | 8-lead SOIC |
Bidirectional means two references, not one
With VREF1 tied to the supply and VREF2 to ground, the output sits at half of the 5 V rail when the shunt current is zero, and a current in either direction moves it up or down around that point. Tie both references to ground and the output starts near ground, so only one current direction is measurable before the amplifier runs out of swing. This sounds obvious, but it is the most common wiring mistake on this family, and the symptom is a channel that reads correctly in one direction and clips in the other. The two reference pins have different input impedances and both must be driven from a low impedance source, or bypassed, otherwise the common-mode rejection degrades at the switching frequency of the load.
Common-mode range above the supply, and why 65 V is not 65 V
The amplifier measures the differential voltage across the shunt while its own supply is 5 V, so the internal input stage has to level-shift the common mode down. The published range of minus 2 V to plus 65 V is where that shift works with the specified accuracy. At the top of the range the accuracy of the shift itself becomes the error, and the datasheet curves show the drift of the offset as the common mode moves. In a 48 V rail with a 65 V transient the part is inside its range; in a 60 V rail with a 75 V transient it is at the survival limit and outside the operating range, so the reading during the transient is not trustworthy even though the part survives.
PWM common mode and the filter that is not there
In a motor phase the common mode is not DC, it is a square wave at the switching frequency with edges of a few tens of nanoseconds. The 80 dB of rejection is specified to 20 kHz, not to 20 kHz plus the edge rate content. What rejects the edge is the matching of the two input resistors inside the part and the matching of the external filter, if there is one. A symmetrical RC pair of 1 kohm and 100 pF on each input, placed close to the pins, moves the edge energy out of the band before it reaches the input stage. Without it, the output shows switching-frequency ripple that no amount of averaging in the processor removes, because it is aliased into the measurement.
Availability and second sourcing
The fixed gain of 20 and the reference pin arrangement are the two things a substitute has to match, and the survivor behaviour at 75 V is the third. The amplifier cross reference page lists the current sense amplifiers by common-mode range and gain, the ADI part second source page separates the grades that share the reference structure from those that do not, and the verification checklist is what to run before a substitute goes into a production board.