AD817ARZ
Product Specifications
AD817ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD817ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD817ARZ: 50 MHz, 350 V per us and an Unlimited Capacitive Load
The AD817ARZ is built for the case where a fast amplifier has to drive something awkward. Most high speed parts specify a maximum capacitive load in the tens of picofarads and become unstable beyond it. This one is rated to drive an unlimited capacitive load while holding 50 MHz of unity gain bandwidth and 350 V per microsecond of slew rate, and it delivers 50 mA minimum from the output stage. Supply range is dual 5 V to 15 V, so the same part works on plus and minus 5 V signal chains and on plus and minus 15 V industrial front ends, and the supply current is 7.5 mA. Settling to 0.1 percent on a 10 V step takes 45 ns, which is the number that matters when the amplifier sits in front of a 12 bit converter with a short acquisition window.
Published values
| Parameter | Value |
|---|---|
| Unity gain bandwidth | 50 MHz |
| Slew rate | 350 V per microsecond |
| Settling time | 45 ns to 0.1 percent, 10 V step |
| Output current | 50 mA minimum |
| Capacitive load | Unlimited |
| Supply | Dual 5 V to 15 V |
| Supply current | 7.5 mA |
| Video flatness | 70 MHz at 0.1 dB, gain of plus one |
| Differential gain and phase | 0.04 percent and 0.08 degrees at 3.58 MHz |
| Bodies | 8-lead plastic DIP and 8-lead SOIC |
Driving a cable without a series resistor
An unlimited capacitive load rating is the reason this part appears at the output of video distribution amplifiers and in front of long cables. A cable presents tens to hundreds of picofarads, and with a conventional amplifier the phase margin collapses and the output rings. Here the output stage is sized so that the load capacitance does not push the loop into instability, which removes the series isolation resistor that would otherwise have to sit between the amplifier and the connector. Removing that resistor also removes the low frequency droop it introduces into a 75 ohm video path, and it is the reason the differential gain and phase figures stay inside 0.04 percent and 0.08 degrees at the color subcarrier frequency rather than degrading at the load.
Where 45 ns settling actually decides the choice
Successive approximation converters with a 1 MSPS throughput give the buffer a few hundred nanoseconds to settle after the sampling switch closes. At 45 ns to 0.1 percent on a 10 V step the AD817 leaves margin for the switch charge injection and for the trace inductance between the amplifier and the converter. Parts with faster small signal bandwidth but slower large signal settling fail here, because the settling tail is what the converter integrates, not the bandwidth. When a board is being reworked because an ADC shows a code dependent offset, the buffer settling is one of the first things to check, and a substitution that changes the settling time by even 20 ns can move the error pattern without changing the average reading.
Power, supplies and the 5 V case
The part is fully specified at a single 5 V supply as well as at dual supplies, which matters because a 5 V signal chain loses headroom on both ends and an amplifier that only meets its numbers at plus and minus 15 V will not hold 50 MHz. At 7.5 mA of supply current the dissipation is 37 mW on a 5 V rail, so a four channel board stays inside a small thermal budget. Decoupling has to be local to each package rather than shared across the board, because the output stage draws current in short bursts when it drives a capacitive load and the resulting supply disturbance is what couples into the adjacent channel.
Keeping a fast amplifier in stock
High speed amplifiers are the first parts to go short when a wafer fab tightens, because the processes behind them are shared with communications parts. The AD817 is a long lived device that still moves through distribution, but the DIP body is the version that disappears first while the SOIC stays available. Boards that were built around the DIP need a footprint change, and that is a build decision rather than a part decision. The amplifier cross reference page lists the families we hold by bandwidth and output drive, the pin to pin cross reference page covers the bodies that swap without a board change, and the drop in replacement verification page walks through the checks that have to pass before a substitute goes on a bill of materials.