Contact Us

AD8066ARZ-R7

Brand: Analog Devices
Analog Devices AD8066ARZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8066ARZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8066ARZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8066ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8066ARZ-R7: Two FET Input 145 MHz Amplifiers in One SOIC

The AD8066ARZ-R7 is the dual member of the FastFET family, supplied on a 7 inch reel in an 8-lead SOIC. Each half has a 1 pA input bias current, 145 MHz of bandwidth at a gain of plus one, 180 V per microsecond of slew rate at a gain of two, 7 nV per root hertz of voltage noise at 10 kHz and 0.6 fA per root hertz of current noise, with 1.5 mV maximum offset, minus 100 dB of common mode rejection and minus 88 dBc of spurious free dynamic range at 1 MHz. Each amplifier draws 6.4 mA, the supply range is 5 V to 24 V, the output is rail to rail and the part does not phase reverse. The pair shares supply pins, which is the only electrical difference from two singles.

Published values

ParameterValue
ConfigurationDual FET input amplifier
Bias current1 pA per input
Bandwidth145 MHz per amplifier at a gain of plus one
Slew rate180 V per microsecond at a gain of two
Voltage noise7 nV per root hertz at 10 kHz
Current noise0.6 fA per root hertz at 10 kHz
Offset voltage1.5 mV maximum
DistortionMinus 88 dBc spurious free at 1 MHz
Supply range5 V to 24 V single supply
Quiescent current6.4 mA per amplifier
Body8-lead SOIC, tape and reel
Temperature rangeMinus 40 to plus 85 degrees Celsius

Twelve point eight milliamps and the shared supply

Two amplifiers at 6.4 mA are 12.8 mA, which is 64 mW on 5 V and 307 mW on a 24 V rail. At the top of the supply range the dual is a real thermal load in an 8-lead SOIC, and the junction rise over ambient has to be added to the ambient before the offset drift and the noise are read from the curves. The shared supply pins also mean that the decoupling has to be at the package and not at the far end of the board, because both halves draw their transient current through the same bond wires and a shared 10 nF capacitor at the wrong distance turns that into a common impedance that couples one channel into the other.

Two halves for a differential front end

The obvious use of a dual FET input part in instrumentation is a differential input stage, where one amplifier buffers the positive input and the other buffers the negative one, and the matching of the two bias currents is what keeps the common mode error small. With 1 pA of bias current the error through a 10 Mohm source is 10 uV, and if the two halves differ by 20 percent the differential error is 2 uV, which is small against the 1.5 mV of offset. That is the arithmetic behind the usual guidance that a FET input pair is chosen for its bias current rather than for its matching.

Rail to rail output from a single supply

The rail to rail output means a single 5 V supply can drive a converter whose input range is 0.5 V to 4.5 V without a negative rail, and the input common mode includes both rails, which is what a photodiode or a piezoelectric sensor needs when its return is at ground. On a 24 V supply the output can swing to within a fraction of a volt of each rail at light load, and the 180 V per microsecond slew rate keeps a 10 V step inside 60 ns, so a high voltage transducer can be driven directly.

Reel, grade and second sourcing

The R7 suffix is the tape and reel packing, not an electrical grade, so the part is identical to the tube version and the choice is a packing one. The automotive qualified version of this family is a separate order code with a different temperature range, so a grade change is a paperwork and a qualification question rather than a drop in substitution. When a socket is being second sourced, the bias current and the input capacitance are the two specifications to compare first, because a part with ten times the bias current will work in a test fixture and fail on a high impedance board. The amplifier cross reference page groups the FET input duals by bias current and bandwidth, the how to verify a drop in replacement page lists the checks that catch a marginal swap, and the obsolete part cross reference hub covers parts that are no longer catalog items.