Contact Us

AD8065ARTZ

Brand: Analog Devices
Analog Devices AD8065ARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8065ARTZ — Analog & Mixed-Signal ICs | Superb Automation

AD8065ARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8065ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8065ARTZ: FET Input, 1 pA of Bias, 145 MHz

The AD8065ARTZ is a single FET input voltage feedback amplifier with a 1 pA input bias current, 145 MHz of bandwidth at a gain of plus one, 180 V per microsecond of slew rate at a gain of two, and 7 nV per root hertz of voltage noise at 10 kHz with 0.6 fA per root hertz of current noise. Offset is 1.5 mV maximum, common mode rejection is minus 100 dB, spurious free dynamic range is minus 88 dBc at 1 MHz, and the quiescent current is 6.4 mA. It runs from a single 5 V to 24 V supply with a rail to rail output, has no phase reversal, and comes in SOIC-8, MSOP-8 and the 5-lead SOT-23 that this order code uses. The dual is the AD8066.

Published values

ParameterValue
Input stageFET input, 1 pA bias current
Bandwidth145 MHz at a gain of plus one
Slew rate180 V per microsecond at a gain of two
Voltage noise7 nV per root hertz at 10 kHz
Current noise0.6 fA per root hertz at 10 kHz
Offset voltage1.5 mV maximum
Common mode rejectionMinus 100 dB
DistortionMinus 88 dBc spurious free at 1 MHz
Supply range5 V to 24 V single supply
OutputRail to rail, no phase reversal
Quiescent current6.4 mA per amplifier
BodiesSOIC-8, MSOP-8, 5-lead SOT-23

One picoamp decides the source impedance ceiling

One picoamp of bias current through a 10 Mohm source is 10 uV, through 100 Mohm it is 100 uV and through 1 Gohm it is 1 mV, which is where it starts to compete with the 1.5 mV offset. That is the whole argument for a FET input part: below about 10 Mohm a bipolar amplifier with 2 nV of noise beats it, and above 100 Mohm nothing else works. Photodiode preamplifiers, pH electrodes, piezoelectric sensors and high value bridge circuits live on the high side of that line, and the 0.6 fA per root hertz of current noise means the shot noise of the source dominates long before the amplifier does.

Seven nanovolts with a 145 MHz bandwidth

Seven nanovolts per root hertz over a 1 MHz measurement bandwidth is 7 uV RMS, which is 4.6 percent of a 16 bit code on a 10 V range and comfortably below the noise of most sources. The combination of low voltage noise and low current noise in one part is what makes it usable across a wide range of source impedances, and it is the reason this family is used in ultrasound preamplifiers and in precision instrumentation where a bipolar part would load the source. The 180 V per microsecond slew rate gives 197 mV peak at full bandwidth, so a large signal at high frequency is limited by slew rather than by bandwidth.

Single supply from 5 V to 24 V

The 24 V maximum supply with a rail to rail output means the same part works in a 5 V portable instrument and in a 24 V industrial front end, and the input common mode includes the rails because the FET stage does not need headroom for a bipolar pair. At 6.4 mA and 24 V the part dissipates 154 mW, which is the point where the SOT-23 body becomes a thermal question and the SOIC or MSOP is the better choice. A board that runs the part at 24 V in the five lead body and expects the same offset drift as at 5 V will see the junction temperature move the offset, because the drift specification assumes a junction near ambient.

Where a FET input part is the wrong answer

Below a few megohms of source impedance a bipolar input part with lower voltage noise wins, and this part's 7 nV is respectable but not the lowest. In a 50 ohm system the source noise is 0.9 nV, so the amplifier's 7 nV is the dominant term if it is the first stage, and a 1 nV bipolar part would give a better noise figure. The decision is made by comparing the source impedance with the crossover, and it is the first calculation in any low noise front end. The amplifier cross reference page groups the FET input and low noise parts by bias current, the ADI part second source page covers the grades that are genuinely equivalent, and the component lead time solutions page shows what can ship against a schedule.