AD8052ARZ
Product Specifications
AD8052ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8052ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8052ARZ: A 110 MHz Dual Amplifier Where the Supply Current Matters as Much as the Bandwidth
The AD8052ARZ is the dual member of a three-part family of voltage feedback amplifiers: the AD8051 is single, the AD8052 is dual and the AD8054 is quad, and all three run on 3 V, 5 V or plus and minus 5 V rails with a rail to rail output. The SOIC order code here is the workhorse body. The two numbers that describe the part honestly are 110 MHz of minus 3 dB bandwidth at unity gain and 4.4 mA of supply current per amplifier, and the second one is the reason the part exists: a 110 MHz amplifier that draws 4.4 mA at 5 V is 22 mW per channel, so a dual is 44 mW, which is the kind of budget a battery instrument or a multichannel data acquisition card can actually carry.
Bandwidth, slew rate and full power bandwidth are three different numbers
The 110 MHz figure is a small signal number at a gain of 1. The slew rate of 145 V per microsecond sets a different limit that depends on the amplitude: a 2 V peak to peak sine can reach about 23 MHz before the output runs out of slew, and a 5 V peak to peak sine reaches about 9.2 MHz. So a stage that has to deliver 5 V peak to peak is a 9 MHz stage and not a 110 MHz stage, and a filter built around the part has to be planned from the amplitude it will actually swing. The 0.1 dB gain flatness figure of 20 MHz into a 150 ohm load is the number that matters for a signal chain with a defined passband, because flatness and not the minus 3 dB point is what keeps a gain calibration valid across the band.
Output drive, settling and the load that changes the answer
The output drives 45 mA while staying within 0.5 V of either rail, which is enough to drive a 100 ohm back terminated cable or a fast analogue to digital converter input without a buffer. Settling to 0.1 percent in 50 ns is what makes the part usable ahead of a multiplexed converter, where the driver has to recover from a channel change inside the acquisition window. Both of those statements are load dependent: the settling time is quoted into a defined load, and a capacitive load of a few tens of picofarads at the converter input adds a pole that a small series resistor has to isolate. The rail to rail output is also not a rail to rail input, and a follower that has to work near the positive rail is where the input stage, not the output stage, becomes the limit.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Channels | 2, dual | The AD8051 single and AD8054 quad share the family |
| Minus 3 dB bandwidth | 110 MHz at a gain of 1 | A small signal number, not a power bandwidth |
| Slew rate | 145 V per microsecond | 9.2 MHz at 5 V peak to peak, 23 MHz at 2 V |
| Settling | 50 ns to 0.1 percent | Fits a multiplexed converter acquisition window |
| Gain flatness | 0.1 dB to 20 MHz into 150 ohm | Keeps a passband calibration valid |
| Output current | 45 mA within 0.5 V of either rail | Drives a terminated cable without a buffer |
| Supply current | 4.4 mA per amplifier | 44 mW for the dual at 5 V |
| Supply range | 3 V, 5 V or plus and minus 5 V | Single supply and split supply from one order code |
| Package | 8-lead SOIC | MSOP body also exists in the family |
Where the part earns its place in a signal chain
Active filters, analogue to digital converter drivers, video and intermediate frequency gain blocks, and transducer front ends that need two matched channels on one die are the natural sockets. Two channels on one die matters more than it looks: the two halves share a supply and a thermal environment, so a differential pair built from one package tracks supply drift far better than two separate singles, and the cost is one package rather than two. Where the requirement is a higher supply voltage or a wider temperature grade, the family is the wrong place to look and a different amplifier should be chosen rather than a different grade of this one.
Second source and board questions
The family is pin compatible across the single, dual and quad within a package family, which makes a channel count change cheap and a vendor change expensive, because the pinout of a dual amplifier is not standardised across vendors. A substitution therefore has to be checked for input bias current, input common mode range, output swing under load and settling, and not only for bandwidth. The ADI part second source page sets out those fields, the pin to pin cross reference covers the package question, and the one stop BOM sourcing page covers buying the amplifier with the converter it drives on a single order.