AD8032ARZ
Product Specifications
AD8032ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8032ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8032ARZ: Two 800 Microamp Amplifiers for One Supply Pin
The AD8032ARZ is the dual member of the family, two of the same 80 MHz rail to rail amplifiers in an 8-lead SOIC or MSOP with a shared supply. Each half draws 800 uA, so the pair costs 1.6 mA and about 8 mW on a 5 V rail, and each half holds 80 MHz at a gain of plus one, 30 V per microsecond of slew rate and 125 ns of settling to 0.1 percent. The output reaches within 20 mV of either rail, the input common mode extends 200 mV beyond the rails with no phase reversal up to 0.5 V beyond, and each output delivers 15 mA. Distortion is minus 62 dB at 1 MHz with a 2 V peak to peak output and minus 86 dB at 100 kHz with 4.6 V peak to peak.
Published values
| Parameter | Value |
|---|---|
| Configuration | Dual, shared supply pins |
| Bandwidth | 80 MHz per amplifier at a gain of plus one |
| Slew rate | 30 V per microsecond |
| Settling time | 125 ns to 0.1 percent |
| Supply current | 800 uA per amplifier |
| Supply range | 2.7 V to 12 V, dual to plus and minus 6 V |
| Output swing | Within 20 mV of either rail |
| Output current | 15 mA per amplifier |
| Input range | 200 mV beyond either rail |
| Distortion | Minus 62 dB at 1 MHz, minus 86 dB at 100 kHz |
| Body | 8-lead SOIC and 8-lead MSOP |
| Temperature range | Minus 40 to plus 85 degrees Celsius |
Two channels on one supply pin, and the coupling that follows
Both amplifiers share a positive and a negative supply pin, and that sharing is the one thing a dual does not do as well as two singles: a fast transient on one output couples into the other through the supply bond wire, and the coupling grows with the load current. With 800 uA of quiescent current the shared impedance is small, so coupling is modest at low output currents and becomes visible when both halves drive capacitive loads at the same time. The usual fix is a decoupling capacitor at each supply pin rather than one at the package edge, and a small series resistor between the two halves if they are in a high gain chain.
Two buffer channels for one converter
The natural use for a dual in a data acquisition front end is one half as the input buffer and the other as the reference buffer, because both need to settle quickly and both can live on the same rail. A successive approximation converter at 1 MSPS needs its reference to recover from the charge drawn during conversion, and a 125 ns settling amplifier with 15 mA of output current is comfortably fast enough for a reference bypassed with a few microfarads. Putting the reference buffer on the same die as the input buffer also keeps the two close together, which shortens the return path for the switching currents.
Power budget across a family
At 1.6 mA for the pair, a four channel analog front end built from two duals draws 3.2 mA, which is 16 mW on 5 V. That is the number that decides whether a portable instrument can run from a 9 V battery for a shift or needs a lithium pack. It also sets the constraint on the converter: a 1 MSPS converter that draws 2 mA alone would double the analog budget, so the pairing of converter and amplifier has to be made on total current rather than on each part separately.
Stability into a capacitive load
The output resistance of a rail to rail stage rises near the rails, so a capacitive load that is stable at mid supply can ring when the output is near a rail. A 100 pF load with a 20 mV swing at 1 MHz is the case that catches people, because the small swing keeps the output near the rail where the resistance is highest. Adding a small series resistor at the output, or isolating the capacitance with a resistor inside the feedback loop, is the standard answer and costs one component per channel. The part is not specified for unlimited capacitive load, unlike some high speed parts, so the load has to be considered part of the circuit. The amplifier cross reference page groups the dual rail to rail parts by current and load drive, the pin to pin cross reference page lists which duals share the eight lead footprint, and the obsolete part cross reference hub covers grades that are no longer catalog items.