AD8031ARTZ
Product Specifications
AD8031ARTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8031ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8031ARTZ: 80 MHz From 800 Microamps in a Five Lead SOT-23
The AD8031ARTZ is the single amplifier in the AD8031 and AD8032 pair, in a 5-lead SOT-23, and its reason to exist is the ratio between bandwidth and current: 80 MHz at a gain of plus one and a 30 V per microsecond slew rate from 800 uA of supply current, which is under 4 mW on a 5 V rail. The input and output are both rail to rail, the output comes within 20 mV of either rail, and the input common mode range extends 200 mV beyond the rails without phase reversal. Settling to 0.1 percent takes 125 ns, distortion is minus 62 dB at 1 MHz with a 2 V peak to peak output and minus 86 dB at 100 kHz with 4.6 V peak to peak, and the output delivers 15 mA. The part is fully specified at 2.7 V, 5 V and plus and minus 5 V.
Published values
| Parameter | Value |
|---|---|
| Bandwidth | 80 MHz at a gain of plus one |
| Slew rate | 30 V per microsecond |
| Settling time | 125 ns to 0.1 percent |
| Supply current | 800 uA per amplifier |
| Supply range | 2.7 V to 12 V, dual supplies to plus and minus 6 V |
| Output swing | Within 20 mV of either rail |
| Input range | 200 mV beyond either rail, no phase reversal 0.5 V beyond |
| Output current | 15 mA |
| Distortion | Minus 62 dB at 1 MHz, minus 86 dB at 100 kHz |
| Offset voltage | 1.5 mV maximum on the high grade |
| Body | 5-lead SOT-23 |
| Temperature range | Minus 40 to plus 85 degrees Celsius |
Four milliwatts changes what a battery product can do
At 800 uA and 5 V the amplifier burns 4 mW, which over a year is 7 Ah, so in a product that runs continuously from a coin cell the duty cycle has to be considered before the part is chosen. Where it does pay is in a portable instrument that is awake for a small fraction of the time: 4 mW of analog front end is affordable when the alternative is a 10 mA part that forces a bigger battery. The 2.7 V minimum supply matters more than the current figure for a two cell alkaline product, because the end of discharge voltage of two cells is 2.0 V and this part stops working before the cells are flat, so a boost converter or a single lithium cell is the realistic supply.
Thirty volts per microsecond and the full power limit
With 30 V per microsecond of slew rate, the largest sine at 80 MHz is 60 mV peak, so the 80 MHz bandwidth describes small signals. At 4.6 V peak to peak, which is the amplitude the distortion figure is quoted at, the full power bandwidth is about 2 MHz. A converter driver running at 1 MHz with a 2 V peak to peak swing is inside the slew limit, and a video stage at 4 V peak to peak and 20 MHz is not, which is why the part is sold as a battery and instrumentation amplifier rather than as a video amplifier. Reading the two numbers together avoids the usual disappointment of a part that measures 80 MHz on a network analyser and misbehaves in a real circuit.
Rail to rail on both ends in a 5-lead body
The output to within 20 mV of either rail means a single supply 3.3 V system can use the full converter range, and the input extending beyond the rails by 200 mV means a signal that overshoots ground does not forward bias the input stage. The 5-lead SOT-23 has one input, one output, one supply pin at each rail and no spare, so the feedback network has to live on the same side of the board as the part, and there is no pin available for a compensation capacitor. That is a board constraint rather than an electrical one, and it is the reason boards with a large capacitive load or a long feedback path use the 8-lead body instead.
Driving a switched capacitor load
The 15 mA output and 125 ns settling make the part usable as a buffer in front of a successive approximation converter whose sampling capacitor has to be charged within the acquisition window. At 1 MSPS the window is a few hundred nanoseconds, and an amplifier that settles to 0.1 percent in 125 ns has enough margin for a 10 pF to 20 pF load if the trace is short. Beyond that the settling becomes a function of the load capacitance and the output resistance rather than of the amplifier, and the 20 mV swing to the rail starts to matter because the top of the converter range is where the last codes live.
What to check before substituting it
The 5-lead SOT-23 pinout is shared with a number of single amplifiers but the compensation is internal and the bandwidth and slew rate differ widely between them, so a pin compatible part is not automatically a working part. The two things to compare are the settling time into the actual load and the phase margin with the feedback network on the actual board, because a faster part with less phase margin can be worse in a circuit that was stable with this one. The amplifier cross reference page groups the micropower rail to rail parts by current and bandwidth, the pin to pin cross reference page lists what shares the five lead footprint, and the how to verify a drop in replacement page sets out the measurements that catch a marginal swap.