AD8022ARZ
Product Specifications
AD8022ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8022ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8022ARZ: A Dual 2.5 nV Amplifier for Receiver Front Ends
The AD8022ARZ is two low noise voltage feedback amplifiers in one package, each drawing 4.0 mA and each contributing 2.5 nV per root hertz of voltage noise at 100 kHz with 1.2 pA per root hertz of current noise. Bandwidth is 130 MHz at unity gain, slew rate is 50 V per microsecond, settling to 0.1 percent is 68 ns, and the output swings to plus and minus 10.1 V on a plus and minus 12 V supply. Spurious free dynamic range is 110 dB at 200 kHz at a gain of seven, multitone power ratio is better than minus 66 dBc, and offset is 1.5 mV typical. The intended use is the receive channel of a digital subscriber line modem, where two matched low noise stages drive the analog to digital converter as a differential pair.
Published values
| Parameter | Value |
|---|---|
| Configuration | Dual voltage feedback amplifier |
| Voltage noise | 2.5 nV per root hertz at 100 kHz |
| Current noise | 1.2 pA per root hertz |
| Bandwidth | 130 MHz at a gain of plus one |
| Slew rate | 50 V per microsecond |
| Settling time | 68 ns to 0.1 percent |
| Output swing | Plus and minus 10.1 V on a plus and minus 12 V supply |
| Distortion | 110 dB spurious free at 200 kHz, MTPR better than minus 66 dBc at a gain of seven |
| Offset voltage | 1.5 mV typical |
| Supply | Plus 5 V, plus and minus 2.5 V to plus and minus 12 V |
| Quiescent current | 4.0 mA per amplifier |
| Bodies | 8-lead MSOP and 8-lead SOIC |
One hundred and thirty megahertz is a small signal number
With 50 V per microsecond of slew rate, the largest sine a 130 MHz bandwidth can support is 61 mV peak, because 50 V per microsecond divided by two pi times 130 MHz is 61 mV. Above that amplitude the output is limited by slew rate, not by bandwidth, and the full power bandwidth falls as the signal grows: at 10 V peak to peak the limit is about 800 kHz. This is not a defect in the part, it is the arithmetic that applies to every voltage feedback amplifier, and it explains why a receiver front end built for millivolt signals can quote 130 MHz while a line driver stage in the same product needs a different amplifier entirely.
Why a receiver wants two matched halves
A differential receive path needs two amplifiers with matched gain, matched phase and matched noise, and putting both halves on one die is how that matching is delivered. The 4.0 mA per amplifier and the 2.5 nV noise apply to each half, so the differential noise is the root sum of the two, about 3.5 nV, which is still low enough for a 12 bit converter on a 1 V signal. Separating the halves into two packages would add noise from the supply and ground difference between them, which appears directly as common mode to differential conversion in the following converter.
Twelve volt supplies and 10.1 V of swing
On plus and minus 12 V the output reaches plus and minus 10.1 V, leaving about 1.9 V of headroom at each rail at the quiescent current, and that headroom shrinks as the load current rises. For a receive path this is more swing than the signal needs, so the supply is chosen for dynamic range rather than for amplitude, and the 24 V total at 8 mA for the dual is 192 mW of quiescent dissipation. A build that runs the same part on plus and minus 5 V loses half the swing and keeps the same noise, which changes the signal to noise ratio for a fixed input level by 6 dB. That is why the supply voltage and the gain have to be chosen together in a receive chain.
Overload recovery and the upstream filter
The part is described as having fast over voltage recovery, which matters because the receive pair sees the transmit signal as a large common mode disturbance on the line. Without fast recovery the first samples after a transmit burst are wrong, and the modem's error rate shows it as a burst error pattern rather than as random noise. The same property makes the part useful as an ultrasound preamplifier, where the transmit pulse is orders of magnitude larger than the echo, and as an instrumentation front end where a sensor can be driven into the rails. The amplifier cross reference page groups the low noise dual parts by supply range, the ADI part second source page covers the grades that are equivalent, and the component lead time solutions page shows what is on the shelf.