AD7927BRUZ-REEL7
Product Specifications
AD7927BRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7927BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD7927BRUZ-REEL7: a 12 bit eight channel converter at 200 kSPS with a channel sequencer
What this order code is
AD7927BRUZ-REEL7 is a 12 bit successive approximation converter with eight single ended inputs and a sequencer that runs a preprogrammed channel list without host intervention. It converts at up to 200 kSPS from a single supply of 2.7 V to 5.25 V, dissipates 3.6 mW maximum at 3 V and 7.5 mW maximum at 5 V at full rate, and goes to 0.5 microamps in shutdown. The serial port is compatible with SPI, QSPI, MICROWIRE and DSP interfaces and there is no pipeline delay, so the result of a conversion is available in the same frame.
The input range is set in the control register as 0 V to the reference or 0 V to twice the reference, with either straight binary or twos complement output coding, which means the same part can be used for a unipolar sensor and for a bipolar signal around a mid rail reference without a second device. The track and hold amplifier handles input frequencies above 8 MHz, so the 200 kSPS rate is limited by the converter and not by the front end. The part is qualified for automotive applications in a 20-lead TSSOP.
Parameters as published
| Item | Value |
|---|---|
| Resolution | 12 bits |
| Throughput | 200 kSPS |
| Inputs | eight single ended with sequencer |
| Supply range | 2.7 V to 5.25 V |
| Power at 3 V, full rate | 3.6 mW maximum |
| Power at 5 V, full rate | 7.5 mW maximum |
| Supply current at 3 V | 1.2 mA maximum |
| Supply current at 5 V | 1.5 mA maximum |
| Signal to noise and distortion | 70 dB minimum at a 50 kHz input |
| Input bandwidth | above 8 MHz |
| Shutdown current | 0.5 microamps maximum |
| Output coding | straight binary or twos complement |
| Body | 20-lead TSSOP |
Numbers that decide the application
The eight channels share one converter, so 200 kSPS across eight inputs is 25 kSPS per channel when the sequencer scans them all. A control loop that needs 10 kSPS on one channel and a slow background scan on seven others can have both, but a system that needs 200 kSPS on every channel needs eight converters or a part with simultaneous sampling. The sequencer is what makes the scan cheap: the host writes the channel list once and reads results in order, which removes the per conversion write that a non sequenced part needs.
The 70 dB minimum signal to noise and distortion at a 50 kHz input is 11.3 effective bits, so the converter delivers about 11.3 of its 12 bits at that frequency and the remaining bit is available only at lower input frequencies or with averaging. One least significant bit on a 2.5 V reference is 610 microvolts, and the reference, not the converter, is usually the larger error in a system built around this part. The 0 to twice the reference mode halves the resolution per volt, taking the step to 1.22 mV, in exchange for a bipolar span.
The power figures are maximums at full rate and they scale with throughput rather than being fixed. At 3 V and full rate the part draws 1.2 mA; a system that converts at 10 kSPS and powers down between conversions draws a fraction of that, which is why the 0.5 microamp shutdown exists. The supply current at 5 V being only 25 percent higher than at 3 V while the power is twice as high is the usual arithmetic and it is why a 3 V rail is the better choice when the analogue front end allows it.
Where it fits and where it does not
It fits multi channel industrial monitoring, motor control feedback, instrument front panels, automotive sensor clusters and any system that scans eight slow channels and needs one fast one. It does not fit simultaneous sampling requirements, a signal that needs more than 11.3 effective bits at 50 kHz, or a channel that needs a differential input, since all eight inputs are single ended and referenced to one ground.
Supply and second source questions
The questions we get are about the reference, the input coding and the sequencer behaviour after a reset, and about whether a 12 bit converter from another family in the same package will read the same control register. Register maps are not standardised, so a substitute needs a firmware change even when the pins line up. The converters with matching pinouts are listed on the converter cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check the body, the packing and the temperature grade, and we confirm the reference arrangement on the line because a converter with an external reference is usually bought with that reference and the two have to be checked together. Where the exact code is short we will say so rather than offer a converter with a different channel count. Send the line items, quantities and required date through the BOM shortage recovery page, and for automotive programmes the power management cross reference page lists the companion rails we hold for the same platforms.
AD7927BRUZ-REEL7 power against throughput: 18 nJ a conversion, and the 60 uA that comes from converting at 10 kSPS
The published maximum is 3.6 mW at 3 V and full rate, and 7.5 mW at 5 V. Divided by the 200 kSPS rate that is 18 nJ and 37.5 nJ per conversion, which is the honest way to compare this part against a slower converter: energy per conversion is what a battery budget consumes, not the headline current. A conversion takes 5 us at full rate, and at 1.2 mA maximum the charge moved per conversion is 6 nC. If the part converts at 10 kSPS and is in shutdown between conversions, the average current is 6 nC times 10,000, which is 60 uA, plus the 0.5 uA of shutdown current. At 3 V that is 0.18 mW against 3.6 mW, a factor of twenty, and it is available without changing the part.
What the sequencer does to the bus
Sixteen clock cycles carry a 12 bit result, so at 20 MHz the transfer is 0.8 us inside a 5 us conversion window, which is 16 percent of the frame. The host is idle for the rest of it, and with a preprogrammed channel list it does not have to write a channel address between conversions. A non sequenced part needs that write, and the write is the same 0.8 us, so the sequenced part halves the bus occupancy at full rate and removes it entirely when the host reads results in a burst after a scan.
Eight channels do not deliver 200 kSPS each
The eight inputs share one converter, so a full scan takes 40 us and each channel sees 25 kSPS. A control loop that needs 10 kSPS on one channel and a background scan on the other seven gets both by putting the fast channel in the list more often, but a system that needs 200 kSPS on every input needs eight converters or a simultaneous sampling part. This is the single most common mistake in a bill of materials built from the headline rate, and it is visible only when the scan time is multiplied out.
The reference, not the converter, is usually the larger error
One least significant bit on a 2.5 V reference is 610 uV, and the 70 dB minimum signal to noise and distortion at a 50 kHz input is 11.3 effective bits, so the converter gives up 0.7 of a bit at that frequency. A reference with 0.1 percent initial accuracy contributes 2.5 mV, which is four codes, and its temperature drift over 100 C at 10 ppm per degree is another 2.5 mV. Selecting a better reference therefore buys more than selecting a converter with one more bit, and the 0 to twice the reference mode, which takes the step to 1.22 mV, is a span decision rather than an accuracy one.
| Throughput | Conversion time | Average current at 3 V | Power at 3 V | Energy per conversion |
|---|---|---|---|---|
| 200 kSPS, full rate | 5 us | 1.2 mA | 3.6 mW | 18 nJ |
| 100 kSPS | 5 us plus idle | 0.6 mA | 1.8 mW | 18 nJ |
| 10 kSPS with shutdown | 5 us plus idle | 60 uA | 0.18 mW | 18 nJ |
| 1 kSPS with shutdown | 5 us plus idle | 6.5 uA | 0.02 mW | 18 nJ |
Converter equivalents are on ADC DAC cross reference, programme purchasing is on OEM procurement, and availability against a build schedule is on component lead time solutions.
Request Quote — In Stock, 100% New & Original, Full Warranty