Contact Us

AD7893ARZ

Brand: Analog Devices
Analog Devices AD7893ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD7893ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD7893ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD7893ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD7893ARZ: Twelve Bits, Six Microseconds and Only Eight Pins

The AD7893 is a 12-bit successive approximation converter with an on-chip track and hold, an on-chip clock, control logic and a two wire serial port, all in an 8-pin body, operating from a single 5 V supply at about 25 mW. The small outline version is the ARZ. The point of the part is what is missing: there is no reference to connect, no multiplexer to drive, no bus to arbitrate and no configuration register. Convert start, serial clock and serial data are the entire digital interface, and the throughput is up to 117 kHz, which is the conversion time of 6 microseconds plus the time needed to read the 12 bits out.

Four input ranges, four order codes, one footprint

The family offers plus or minus 10 V as the -10, plus or minus 2.5 V as the -3, 0 V to 2.5 V as the -2 and 0 V to 5 V as the -5, and every one of them is the same 8-pin package. The range is therefore a purchasing decision rather than a routing decision, and a buyer has to confirm which suffix is on the reel. The value of one code differs by a factor of eight across the family: 4.88 mV on the plus or minus 10 V range, 1.22 mV on the plus or minus 2.5 V and the 0 V to 5 V ranges, and 610 uV on the 0 V to 2.5 V range. Choosing the widest range by habit costs three bits of resolution on a signal that only occupies a quarter of it.

Dynamic performance is specified, not assumed

The part is specified for harmonic distortion and signal to noise ratio as well as for the usual direct current parameters, which matters because a 12-bit converter used at 100 kHz of bandwidth is limited by its dynamic behaviour rather than by its linearity. The vendor's own plot of effective number of bits against frequency, taken at a 102.4 kHz sampling rate on the 0 V to 2.5 V member, shows 11 effective bits at a 51.2 kHz input. That is one bit below the 12-bit word length at the top of the band, and it is the honest figure to compare against a requirement.

ParameterValueWhat it decides
Resolution12 bits4096 codes
Conversion time6 microsecondsThroughput up to 117 kHz with a fast read
Input rangesPlus or minus 10 V, plus or minus 2.5 V, 0 to 2.5 V, 0 to 5 VOne code is 4.88 mV to 610 uV depending on suffix
Track and holdOn chipNo external sample and hold
ReferenceExternal, brought to a dedicated pinThe full scale is chosen by the user
SupplySingle 5 V25 mW typical, suitable for portable instruments
InterfaceTwo wire, serial clock in and data outThree digital lines including convert start
Effective bits11 at 51.2 kHz input, 102.4 kHz samplingOne bit below the word length at the band edge
Package8-pin mini DIP and 8-pin SOICSmallest footprint in this class

The serial clock can be read during or after the conversion

The two wire port lets the host read the previous result while the next conversion is running, or wait until the conversion completes and read afterwards. Reading during the conversion is faster and is what reaches the 117 kHz figure, but the vendor notes that the timing of the clock edges relative to the internal bit trials affects the noise floor, so a system that reads during conversion should check its own noise performance rather than assume the datasheet histogram applies. Reading after conversion is slower and quieter, which is the right trade for a measurement instrument that has the time.

Where the part fits

Portable and battery powered instruments, data acquisition, and any board where a 12-bit channel has to be added without disturbing the rest of the board: an 8-pin part with three digital lines and one analogue input can be placed next to the sensor and read by a microcontroller shift port. Where the converter has to be shared between channels, a multiplexed part with a sequencer is the better answer, and where 12 bits is not enough at this speed, the next family up offers more resolution with more pins. For comparisons, the ADC and DAC cross reference page lists the classes, the component lead time solutions page covers supply, and the supplier quality audit page covers verification of small outline parts on receipt.

Six microseconds of conversion inside an 8.5 microsecond cycle

The 117 kHz throughput figure is the conversion time plus the read time, not the conversion time alone. One cycle at 117 kHz is 8.55 microseconds, the conversion takes 6 microseconds, so about 2.5 microseconds remain for the host to clock out 12 bits, which needs a serial clock of roughly 5 MHz. A host with a 2 MHz port cannot reach the ceiling because the read takes 6 microseconds on its own, and the real limit becomes about 83 kHz. That is the number to quote in a specification that names a processor, because it describes the system rather than the converter, and it is the reason the same part appears to perform differently on two boards.