AD7797BRUZ
Product Specifications
AD7797BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7797BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7797BRUZ: 24 Bits, 65 Nanovolts of Noise and a Rate You Choose in Software
The AD7797 is the 24-bit member of a two part pair, with the AD7796 as its 16-bit sibling, and both are built for bridge sensors with a fixed gain of 128 instrumentation amplifier in front of the converter. This order code is the 16-lead TSSOP body specified from minus 40 C to plus 85 C, drawing 250 uA typical from a 2.7 V to 5.25 V supply with 1 uA in power-down. Unlike the pin strapped front ends in the same family, the output data rate here is software programmable across a range from 4.17 Hz to 123 Hz, which puts the rate and the filter response under firmware control.
Sixty five nanovolts in the context of one code
The noise specification is 65 nV rms. With a 2.5 V reference and a gain of 128 the differential input span is about 39 mV, so one 24-bit code is 4.65 nV and the stated noise is about 14 codes, which is a little under 18 bits of rms resolution. That is a strong result for a part at this current, and it is worth keeping in the same sentence as the 24-bit word length, because a specification that quotes only the word length would suggest a resolution four to five bits better than the part delivers. The 4.17 Hz rate is where the 65 nV is reached; at 123 Hz the noise is higher, and the vendor's table gives the figure for each rate for the same reason.
Rates from 4.17 Hz to 123 Hz and what they are for
The lowest rate, 4.17 Hz, is the one that rejects both 50 Hz and 60 Hz simultaneously, so it is the setting for a scale in a market where either mains frequency may be present. Higher rates trade rejection and noise for update speed, which a control loop needs when it is tracking a changing weight rather than a static one. The settling time follows the rate, so a firmware routine that switches rate at run time must also allow the filter to settle before it trusts a reading, otherwise the first conversions after the change carry the previous state.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 24 bits | 4.65 nV per code at a gain of 128 on 2.5 V |
| RMS noise | 65 nV | About 14 codes, just under 18 bits rms |
| Amplifier gain | Fixed 128 | 39 mV of input span, bridge sensors connect directly |
| Inputs | One differential channel | One bridge per part |
| Output rate | 4.17 Hz to 123 Hz, software set | 4.17 Hz rejects 50 Hz and 60 Hz together |
| Temperature sensor | Internal, connected to the converter | Bridge temperature compensation without a second part |
| Clock | Internal oscillator or external clock | No crystal unless timing has to be exact |
| Current | 250 uA typical, 1 uA in power-down | 750 uW at 3 V, and effectively zero between reads |
| Supply | 2.7 V to 5.25 V | Battery and 5 V systems from one code |
| Temperature | Minus 40 C to plus 85 C | The 16-bit sibling shares this range |
| Package | 16-lead TSSOP | Independent interface supply for mixed logic |
The temperature sensor is part of the measurement, not an extra
The on-chip temperature sensor is internally connected to the converter, so reading it costs a channel selection and no additional component. In a bridge application that is the correction input that matters most: the gauge factor of a strain gauge and the modulus of the spring element both move with temperature, and a scale that ignores the sensor temperature drifts with the room. Because the sensor is on the die rather than on the bridge, it measures the board temperature, which is close to the bridge only if the two share a thermal environment; a bridge mounted away from the board needs its own sensor or a compensation that is characterised over temperature instead of measured.
Where it fits
Weigh scales, strain gauges, industrial process control, instrumentation and portable instruments are the stated applications. The choice between this part and a pin strapped front end is essentially whether firmware should own the rate: a fixed 10 Hz scale can use a part with no configuration bus, while a product that must serve several ranges or update rates from one hardware build needs the software programmable rate. Between this part and its 16-bit sibling, the decision is resolution against cost on the same footprint. For sourcing, the ADC and DAC cross reference page lists the pair, the obsolete part cross reference hub page covers what to do if a code is withdrawn, and the supplier quality audit page covers verifying the source on parts of this class.