AD7740YRMZ-REEL7
Product Specifications
AD7740YRMZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7740YRMZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD7740YRMZ-REEL7: a synchronous voltage to frequency converter with a 1 MHz input range
What this order code is
AD7740YRMZ-REEL7 is a synchronous voltage to frequency converter that takes an analogue input from 0 V to the reference and produces a pulse train whose frequency is set by the input and by the clock on the CLKIN pin. The full scale output frequency is synchronous with that clock, which means the conversion is a ratio and not a time constant, so the accuracy follows the clock and the reference rather than the tolerance of a capacitor. The part runs from 3.0 V to 3.6 V or 4.75 V to 5.25 V, draws 0.9 mA and dissipates about 3 mW.
Two input modes are available and the BUF pin selects between them. Buffered mode presents a very high input impedance and accepts 0.1 V to VDD minus 0.2 V, which suits a sensor with a significant source resistance. Unbuffered mode accepts minus 0.15 V to VDD plus 0.15 V, which allows a true minus 150 mV input without a charge pump and is the mode to use for a signal that goes below ground. The on chip reference is 2.5 V and it can be overdriven by an external reference anywhere from 2.5 V to VDD.
Parameters as published
| Item | Value |
|---|---|
| Function | synchronous voltage to frequency conversion |
| Maximum input frequency | 1 MHz |
| Output frequency span | 10 percent to 90 percent of the clock |
| Nominal input range | 0 V to the reference |
| Input below ground | minus 150 mV without a charge pump |
| Reference range | 2.5 V to the supply, internal 2.5 V available |
| Buffered input range | 0.1 V to VDD minus 0.2 V |
| Unbuffered input range | minus 0.15 V to VDD plus 0.15 V |
| Supply | 3.0 V to 3.6 V or 4.75 V to 5.25 V |
| Supply current | 0.9 mA |
| Power | about 3 mW typical |
| Body | 8-lead SOT-23 or 8-lead MSOP |
| Grade, this code | Y, guaranteed over the automotive range |
Numbers that decide the application
The transfer function is the first thing to fix. With a 1 MHz clock the output runs from 100 kHz to 900 kHz across the input range, so the span is 800 kHz for a 2.5 V reference, which is 320 kHz per volt or 0.32 Hz per microvolt. A counter with a 100 millisecond gate resolves 10 Hz, which at that slope is 31 microvolts, so the resolution of the system is set by the gate time and the clock and not by the converter. Doubling the gate time halves that figure.
The synchronous architecture is why the part is used in isolated measurements. Because the output frequency is a ratio of the clock, an isolator that passes the clock and the output through the same barrier cancels the propagation delay of the barrier, and the reading stays correct even when the isolator drifts with temperature. An asynchronous converter cannot do that, because its output has no reference to the clock to cancel against.
The two input ranges are not a detail. In buffered mode the input impedance is high but the range stops at 0.1 V above ground and 0.2 V below the supply, so a sensor that saturates to the rail is outside the window. In unbuffered mode the range extends below ground and above the supply, which is what the minus 150 mV figure describes, but the input impedance is no longer high and the source has to be able to drive the switched capacitor input. A channel that moves between modes without checking the source impedance will see a gain error that looks like a reference error.
Where it fits and where it does not
It fits isolated or optically linked measurements, thermocouple and bridge signals that are sent as a frequency over a barrier, sensor interfaces in noisy environments where a frequency is easier to transmit than a voltage, and any low cost conversion where the clock is already available. It does not fit a fast changing signal, since the update rate is the gate time, or a system without a stable clock, because the clock accuracy becomes the measurement accuracy.
Supply and second source questions
The questions we get are about the clock source, the gate time and the input mode, and about whether the part can run from a 3.3 V rail with the internal reference, which it can only if the reference is not required to be 2.5 V at the very bottom of the supply tolerance. Voltage to frequency parts are a small category and the substitutes are not pin compatible, so the comparison has to start from the transfer function. The parts in this class are listed on the converter cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check the body, the grade and the packing, since the Y grade is a temperature guarantee and not a performance grade, and a part in the same family without it will not hold the specification over the automotive range. Send the line items, quantities and required date through the BOM shortage recovery page, and for industrial instrumentation that needs the same conversion over a long production life, the obsolete part cross reference hub lists the parts we can still support after the vendor moves on.
Request Quote — In Stock, 100% New & Original, Full Warranty