AD7738BRUZ
Product Specifications
AD7738BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7738BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7738BRUZ: Eight Single-Ended Channels, Small Ranges and a Multiplexer You Can Reach Into
The AD7738 is the multi channel member of the same family as the AD7732, and it solves a different problem. It brings eight single-ended or four fully differential inputs to a 24-bit converter, with bipolar or unipolar ranges of 625 mV, 1.25 V and 2.5 V, and it accepts a common mode voltage from 200 mV above the analogue ground to 300 mV below the analogue supply. The ranges are deliberately small, because the part is meant for low level signals that would otherwise lose their resolution in a wide range front end.
The multiplexer output is pinned out
MUXOUT and ADCIN are both brought to the package, which means the signal path can leave the chip between the multiplexer and the converter. That single feature changes what the part can be used for: a programmable gain stage, a filter, an isolation amplifier or a current to voltage converter can be inserted in the path, and the multiplexer still does the channel selection ahead of it. It is also the pin pair that lets an engineer check where a signal problem comes from, since the multiplexer output can be observed directly. The cost is two more pins and one more decision in the signal chain.
Resolution against rate, stated three ways
At 500 Hz the part gives 18 bits peak to peak, which is 21 bits effective. At 8.5 kHz it gives 16 bits peak to peak and 19 bits effective, and at 15 kHz it gives 15 bits peak to peak and 18 bits effective. The conversion time at the 8.5 kHz point is 117 microseconds. Working the numbers on the smallest range, a bipolar 625 mV range has a 1.25 V span, so 16 bits peak to peak at 8.5 kHz means the reading is stable inside about 19 uV, and on the 2.5 V range 15 bits peak to peak means stability inside about 152 uV. Those are the figures to compare with the resolution of the sensor, not the 24-bit word length.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 24 bits, no missing codes | Code set is complete at every rate |
| Nonlinearity | 0.0015 percent | About 393 codes, above the noise floor |
| Channels | Eight single-ended or four differential | Up to eight field signals on one part |
| Input ranges | 625 mV, 1.25 V, 2.5 V, bipolar or unipolar | 19 uV of stability on the narrowest range |
| Common mode | 200 mV to supply minus 300 mV | Limits how far the signal ground can float |
| Noise free resolution | 18 bits at 500 Hz, 16 bits at 8.5 kHz, 15 bits at 15 kHz | The number to match against the sensor |
| Conversion time | 117 microseconds at 8.5 kHz | Channel switching at 8.5 kSPS |
| Signal path | MUXOUT and ADCIN pinned out | External gain or filtering inside the multiplexed path |
| Supply | 5 V analogue, 3 V or 5 V digital | Mixed logic levels on one board |
| Temperature | Minus 40 C to plus 105 C | Extended industrial range |
| Package | 28-lead TSSOP | Eight channels in a narrow body |
Calibration per channel, and the reference question
System calibration is stored per channel, so a board with eight sensors of slightly different sensitivity can hold eight corrections instead of one compromise. The differential reference input carries no reference detect, so a missing reference is visible to firmware. Because the ranges are small, the reference choice sets the absolute scale directly: with a 2.5 V reference the 2.5 V range spans the full reference, while the 625 mV range uses a quarter of it. A system that runs the narrow range should consider a smaller reference so that the converter is not throwing away three quarters of its input span, and it should note that the common mode window follows the analogue supply, not the reference.
Where it fits
PLCs and distributed control systems, multiplexed instrumentation and process control are the applications named for this part. It suits a card that has to scan eight low level channels of the same type, such as thermocouples, strain gauges or current loops through a sense resistor, and it suits a product that needs an external amplifier between the multiplexer and the converter. Where the signals are wide range industrial voltages, the AD7732 with its plus or minus 10 V inputs and 16.5 V overvoltage tolerance is the better member; where four single-ended inputs are enough, the AD7734 sits between them. The ADC and DAC cross reference page lists the family comparisons, the incoming inspection plan page covers what to verify on receipt, and the BOM consolidation page covers collapsing several converter codes into one.