AD7606BSTZ
Product Specifications
AD7606BSTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7606BSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7606: Eight 16-Bit Channels Sampling at the Same Instant
The AD7606 is an eight channel data acquisition system that samples all its inputs simultaneously, converts them to 16 bits at 200 kSPS per channel, and does it from a single 5 V analog supply with a separate 2.3 V to 5 V logic supply. Each input is a true bipolar range of plus or minus 10 V or plus or minus 5 V, presented at 1 megohm, clamped for protection and filtered by a second order antialiasing network on chip. Signal to noise plus distortion is 95.5 dB, total harmonic distortion minus 107 dB, integral and differential nonlinearity plus or minus 0.5 LSB, and the whole part dissipates 100 mW from a 5 V rail, falling to 25 mW in standby.
Simultaneous sampling is not a feature, it is a requirement
An eight channel system built from a multiplexed converter samples channel one and channel eight several microseconds apart. In a three phase power measurement that gap is a phase error between voltage and current, and the error moves with load because the phase angle moves. In a motor control loop it means the currents are not all measured at the same rotor position. Simultaneous sampling removes the term entirely: an eight channel track and hold front end captures all inputs on one edge, and the converter then works through them. The 200 kSPS figure applies to every channel at once, not divided between them, which is why the part suits a protection relay that has to look at eight currents and voltages within one power cycle.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Channels, resolution | 8 channels, 16 bits | AD7606-6 has 6, AD7606-4 has 4, same family |
| Sampling | 200 kSPS on all channels simultaneously | Not multiplexed, no aperture skew between channels |
| Input ranges | Plus or minus 10 V and plus or minus 5 V true bipolar | Selected by a pin, no external level shifting |
| Input impedance | 1 megohm, buffered | Second order antialiasing filter on each channel |
| Accuracy | Plus or minus 0.5 LSB INL and DNL | 16 bits with no missing codes |
| Dynamic performance | 95.5 dB SNR, minus 107 dB THD | Measured with a 1 kHz input, full scale |
| Protection | 7 kV ESD on the analog inputs, clamp protection | Inputs survive an overrange without external clamps |
| Supplies | 5 V analog, 2.3 V to 5 V logic | 100 mW active, 25 mW standby |
| Package, temperature | 64-lead LQFP, minus 40 C to plus 85 C | Parallel or serial interface, SPI and DSP modes |
The 1 megohm input and what it saves
A 16-bit converter with a switched capacitor input needs a buffer and often an external amplifier per channel to settle the sampling transient. Eight channels means eight amplifiers, eight sets of resistors and a lot of board area in front of the converter. The AD7606 puts a buffered 1 megohm input and a second order filter on every channel, so a resistive divider from a 240 V line, or a shunt with a divider, can drive the input directly as long as the source impedance stays low enough for the filter to settle. That is the difference between an eight channel measurement card that fits on one board and one that needs a front end card of its own. The filter corner is fixed, so a signal with content above it will alias, and that has to be checked against the application rather than assumed away.
Oversampling, interfaces and the two ways it is used
The on-chip digital filter can average oversampled results, trading throughput for noise: at 200 kSPS the full bandwidth is available, and at lower output rates the same part delivers more effective resolution, which is useful in a weighing or strain application where the signal is slow and the noise floor is the limit. The interface can be parallel, for a processor with a wide bus and a fast read, or serial SPI and DSP modes for a processor with fewer pins. Both read the same conversion results, so the choice is a board level one rather than a firmware one, and an existing product can move between the two without changing the converter. Power line monitoring and protection, multiphase motor control and multiaxis positioning are the applications where the combination of simultaneous sampling and in-range bipolar inputs is what makes the part attractive.
Procurement and second source
The eight channel member of the family is the one that goes short first, and the six and four channel versions share the interface and the register behaviour, so a lower channel count can carry a prototype while the eight channel part is on order. The ADC DAC cross reference covers the family and its competitors, medical device components describes the sourcing route for instrument grade converters, and the checks that catch a reflow damaged part before it reaches a board are set out in the incoming inspection plan.