AD7524JRZ
Product Specifications
AD7524JRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7524JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7524JRZ: An 8-Bit Multiplying DAC Whose Reference Input Is the Signal
The AD7524 is an 8-bit CMOS digital to analog converter with on chip data latches, built for direct connection to a microprocessor bus. Its distinguishing property is that the reference input is a multiplying input: the output is the product of the digital code and the voltage at the reference pin, so the part can attenuate, scale or modulate an analog signal rather than only produce a fixed fraction of a reference. It runs from 5 V to 15 V, is TTL and CMOS compatible at 5 V, guarantees monotonicity over the full temperature range, dissipates under 10 mW typical, and the commercial J grade in the 16-lead SOIC has a 1/2 LSB nonlinearity specification.
39 mV per code on a 10 V reference, 3.9 mV on 1 V
Because the reference is an input, the code size depends on the signal applied to it: a 10 V reference gives 39 mV per code and a 1 V reference gives 3.9 mV. That is the property that makes a multiplying converter useful in a gain control loop, where the reference is the signal being controlled and the code is the gain. It also means the accuracy of the product depends on the reference source impedance and its drive capability, because the reference pin sees the ladder's switched impedance, which varies with code. A source that is not stiff enough produces distortion that looks like converter nonlinearity and is not.
Two quadrant and four quadrant operation
With a fixed polarity reference the part multiplies in two quadrants: the code is unipolar and the output follows the reference sign, so a negative reference gives a negative output. Four quadrant multiplication needs a bipolar reference, which the part accepts, and a current to voltage converter at the output that holds the output node at virtual ground. The difference matters in a modulator: a two quadrant arrangement cannot pass through zero without a code change, so it produces a discontinuity at the zero crossing, and a four quadrant arrangement is required wherever the signal changes sign.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 8 bits | 256 codes of the reference input |
| Reference input | Multiplying, analog | A 10 V reference gives 39 mV per code |
| Nonlinearity, J grade | 1/2 LSB | 19.5 mV on a 10 V reference |
| Monotonicity | Guaranteed over temperature | No code reversal as the code increases |
| Input latches | On chip, bus compatible | A single write cycle holds the code |
| Interface | Parallel, TTL and CMOS | Direct connection to a host data bus |
| Supply range | 5 V to 15 V | The reference can swing close to the supply |
| Dissipation | Under 10 mW typical | No thermal question in a 16-lead body |
| Output | Current, into an external amplifier | The converter needs a current to voltage stage |
| Quadrants | Two, or four with a bipolar reference | Four quadrant needs a virtual ground amplifier |
| Speed | Bus write of a few hundred nanoseconds | Faster than most control loops need |
| Package | 16-lead SOIC, wide body | The J grade on this page |
| Process | CMOS with thin film resistors | Ratio matching that does not drift with the code |
The external amplifier is part of the converter
The output is a current, so the voltage that appears depends entirely on the amplifier that converts it. An amplifier with 1 mV of offset puts 1 mV of error into a 10 V full scale, which is 0.04 percent, and one with 10 mV puts in 0.4 percent, which is half a code at 8 bits. The same amplifier's input bias current flows through the ladder's Thevenin resistance and adds a code dependent error. Choosing a low offset, low bias current amplifier is not optional with a current output converter, and the cheapest part that works is usually a precision bipolar input amplifier rather than a CMOS one.
Why a multiplying converter is still bought
A digital potentiometer can do some of the same jobs, but it has a limited reference range, a wiper resistance that varies with code and a much smaller bandwidth. A multiplying converter has none of those limits and its transfer function is defined by the code and the reference alone. In a programmable gain stage, an automatic gain control loop or an analog modulator for a lock in amplifier, the multiplying converter is still the simplest part that does the job, which is why an 8-bit part from an old process is still in production decades after it was introduced.
Latch behaviour and bus timing
The on chip latches load on the write strobe, and the code is held until the next write, which means the host does not have to refresh the value. That is the difference between this part and a multiplying converter without latches, where the output follows the bus and a glitch on the address lines changes the gain. The latch also means the part can sit on a shared bus, with the chip select deciding which device takes the data. The timing requirement is a data setup and hold window around the strobe, and at the part's speed the bus is almost always the slower element.
Procuring a multiplying converter
The grade suffix sets the nonlinearity and the temperature range, so the J and K grades are not interchangeable in a specification that quotes 1/2 LSB. Parts that multiply an analog reference and can be compared on resolution, reference range and interface are listed in ADC DAC cross reference, the route for an obsolete converter in a legacy board is covered in obsolete part cross reference hub, and the test that catches a wrong grade on receipt is in incoming inspection plan.