AD7490BRUZ
Product Specifications
AD7490BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7490BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7490BRUZ: Sixteen Inputs, 1 MSPS and a Built-In Sequencer
The AD7490BRUZ is a 12 bit converter with sixteen single ended inputs and an on chip sequencer, so a single package can scan a whole bank of sensors without the host addressing each channel. Throughput is 1 MSPS, the supply range is 2.7 V to 5.25 V, power is 5.4 mW maximum at 870 kSPS on a 3 V supply and 12.5 mW maximum at 1 MSPS on 5 V, and signal to noise ratio is 69.5 dB at a 50 kHz input. The part has no pipeline delay, an SPI, QSPI, MICROWIRE and DSP compatible serial interface, and it is qualified to AEC-Q100 for automotive use. The body is a 28-lead TSSOP, with a 32-lead LFCSP alternative.
Published values
| Parameter | Value |
|---|---|
| Resolution | 12 bits |
| Inputs | 16 single ended, with sequencer |
| Throughput | 1 MSPS |
| Supply | 2.7 V to 5.25 V |
| Power | 5.4 mW maximum at 870 kSPS on 3 V, 12.5 mW maximum at 1 MSPS on 5 V |
| Signal to noise | 69.5 dB at 50 kHz input |
| Pipeline delay | None |
| Qualification | AEC-Q100 for automotive applications |
| Interface | Serial, SPI, QSPI, MICROWIRE and DSP compatible |
| Bodies | 28-lead TSSOP and 32-lead LFCSP |
The sequencer removes a host interrupt per channel
Without a sequencer the host has to write the channel address before each conversion, which costs an interrupt and a bus transaction per channel. The on chip sequencer steps through a programmable list of channels by itself, so a scan of sixteen inputs becomes sixteen conversions and one result read per channel, with the addressing handled inside the part. In a system with a hundred sensors that is the difference between a processor spending its time on the converter and a processor spending its time on the measurement. The sequencer also keeps the timing between channels deterministic, which matters when the readings are compared against each other rather than used individually.
Sixteen single ended inputs and the ground reference
Single ended inputs all refer to one ground pin, so the accuracy of every channel depends on that pin being the same potential as the sensors' own reference. In a machine with motors or relays the ground at the converter is not the ground at the sensor, and the difference appears as an offset that moves with load current. Running a dedicated analog ground return to the sensor bank, and keeping the digital return separate until the single point where they meet, is what keeps sixteen channels reading consistently. A part with differential inputs relaxes that requirement, which is why the channel count and the input topology are chosen together.
Automotive qualification and what it changes
An AEC-Q100 qualified version is tested to a different set of stress conditions and has a documented change control process, which is what a tier one supplier needs to put a part on a vehicle program. The electrical specifications are the same as the industrial part; the difference is the qualification file and the temperature grade. In practice the automotive grade is the version that stays available longest, because vehicle programs require long term supply commitments, so a part that is short in the industrial grade is sometimes still reachable through the automotive one, subject to the customer's own approval.
Power at 870 kSPS versus 1 MSPS
The two power figures are quoted at two different throughputs, and that is not an accident: the part's current scales with the conversion rate, so the 3 V figure is taken at the rate that a 3 V system can actually sustain on a slow clock. Comparing a 3 V figure at 870 kSPS with a 5 V figure at 1 MSPS gives a fair picture of what the part costs in each type of system, while comparing two data sheet maxima taken at different rates does not. In a battery instrument the average power is set by the duty cycle and the standby state, so the peak figure matters less than how quickly the part can be parked. The converter cross reference page lists the multi channel parts we hold by input count and rate, the ADI part second source page covers equivalents including automotive grades, and the lead time page shows both bodies.