AD7192BRUZ
Product Specifications
AD7192BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7192BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7192BRUZ: 11 nV of RMS Noise at 4.7 Hz Is About Five Codes at Gain 128
The AD7192 is a 24 bit sigma-delta converter with an on chip programmable gain amplifier, two differential or four pseudo differential inputs, an output data rate from 4.7 Hz to 4.8 kHz and a supply current of 4.35 mA from a 3 V to 5.25 V analog rail. At the slowest rate and a gain of 128 the rms noise is 11 nV, and at a gain of 1 the part delivers up to 22 noise-free bits. Offset drift is 5 nV per degree Celsius and gain drift is 1 ppm per degree Celsius, both specified over time as well as temperature, which is what separates an instrument converter from a general purpose one.
Putting 11 nV in the same units as a code
At a gain of 128 with a 2.5 V reference, the differential input span is 39.06 mV and one code of a 24 bit result is 2.33 nV. The 11 nV of rms noise is therefore 4.7 codes rms, and a peak to peak figure of about six times that, near 28 codes, leaves roughly 19 noise-free bits. That is the number to compare with a load cell: a 2 mV per volt bridge at 5 V excitation gives 10 mV full scale, which at 128 gain is well inside the range, and 19 noise-free bits resolve one part in 500,000 of it.
Filter choice changes the noise, the settling and the rejection
The part has two digital filter options. The sinc filter gives the lowest noise at a given rate but its settling time is several conversion periods, so a channel change costs several readings. The other option trades noise for a faster settle and allows the zero latency mode, in which each conversion is fully settled and can be read as soon as it is available. In a multiplexed system scanning four channels, the difference is between reading 4.7 samples per second per channel and losing the first sample after every switch.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 24 bit, no missing codes | Full code range for a ratiometric measurement |
| Output rate | 4.7 Hz to 4.8 kHz | Three decades of speed against noise |
| RMS noise at 4.7 Hz, gain 128 | 11 nV | 4.7 codes at a 39.06 mV span |
| Noise-free bits at gain 1 | Up to 22 | 22 bits of stable reading from 24 bits of output |
| Gain range | 1 to 128 | Small signals reach the converter without a preamp |
| Input channels | 2 differential, 4 pseudo differential | A bridge pair or a four point measurement |
| Offset drift | 5 nV per degree C | 165 uV over a 100 degree span is avoided |
| Gain drift | 1 ppm per degree C | 0.01 percent over 100 degrees |
| Line rejection | 50 Hz and 60 Hz simultaneously | Both mains frequencies in one setting |
| Clock | Internal 4.92 MHz or external | One pin fewer, or a shared system clock |
| Supply current | 4.35 mA | 21.75 mW at 5 V |
| Analog supply | 3 V to 5.25 V | Runs from the same rail as the bridge |
| Package | 24-lead TSSOP | Board area for the reference and the input filter |
Drift, not offset, is the specification to buy on
An offset of a few microvolts can be removed with a single calibration at one temperature. A drift of 5 nV per degree Celsius cannot: over a 100 degree span it is 500 nV, which at 128 gain and a 39 mV span is 20 codes. The gain drift of 1 ppm per degree Celsius contributes 100 ppm over the same span, which on 24 bits is far larger than either, so a system that needs absolute accuracy has to either hold the temperature or calibrate the gain against a reference at the operating temperature.
The reference is the other half of the accuracy
Every noise and drift figure above is referred to the input, and the reference enters the transfer function directly. A reference with 3 ppm per degree Celsius drift contributes 300 ppm over a 100 degree span, which is larger than the converter's own gain drift, so the reference choice sets the limit. The ratiometric arrangement, where the bridge and the reference run from the same excitation, cancels most of that term and is the usual answer in weigh scales.
Buying a precision converter
The numbers to compare across candidates are rms noise at the intended rate, noise-free bits at the intended gain, and drift, and the order code carries the package. A part that quotes a high resolution and no noise figure per rate cannot be compared at all. Availability is tracked through ADC DAC cross reference, and the wider question of what an instrument needs around the converter is set out in medical device components. Where the original code is short, the options are in component lead time solutions.