AD712JRZ
Product Specifications
AD712JRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD712JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD712JRZ: A BiFET Dual That Replaces the LF412 With Real Specifications
The AD712JRZ is a precision BiFET dual operational amplifier and the data sheet positions it as the enhanced replacement for the LF412 and the TL082, which is the honest way to describe a part like this: it is a pinout compatible upgrade for the workhorse BiFET duals, with guaranteed rather than typical ac specifications. For the J grade the minimum slew rate is 16 volts per microsecond and the minimum unity gain bandwidth is 3 MHz, both guaranteed rather than typical, and the K grade publishes 200 volts per millivolt of open loop gain as a minimum. The input stage is JFET, so bias current is in the picoampere range and stays low at high temperature, which is what keeps a high impedance node from drifting. Surface mount bodies are available on tape and reel to EIA-481A, and MIL-STD-883B versions exist.
Published values
| Parameter | Value |
|---|---|
| Channels | 2 |
| Input stage | BiFET, junction field effect input |
| Slew rate, J grade | 16 volts per microsecond minimum |
| Unity gain bandwidth, J grade | 3 MHz minimum |
| Open loop gain, K grade | 200 volts per millivolt minimum |
| Replacement for | LF412, TL082 |
| Single version | AD711 |
| Bodies | DIP, surface mount and cerdip |
| Tape and reel | Surface mount to EIA-481A |
| Military versions | MIL-STD-883B available |
Guaranteed minimums are the reason to pay for this part
A TL082 data sheet quotes typical slew rate and bandwidth, and a production lot that comes in at 60 percent of typical still passes. A part with guaranteed minimums lets an engineer size a filter or a sample and hold around the worst case rather than around a hope, which matters when the same board is built for a decade. That is the whole value proposition of an enhanced replacement: the pinout is the same, the supply range is the same, and the guarantee is stronger.
Where a BiFET dual still wins
A CMOS input amplifier has lower bias current and lower cost, but its input capacitance and its noise behaviour at low frequency differ, and its common mode range often stops short of the rails. A JFET input part tolerates a high impedance source with a bias current that stays low over temperature and has a well behaved 1/f corner. For active filters with megohm resistors, sample and hold buffers and charge amplifiers, that combination is still hard to beat, and the dual body with a shared supply pin keeps the board simple.
Substitution and stock
Because the part is sold as a replacement for two very common types, the substitution question runs the other way: buyers ask whether the LF412 or TL082 can replace it, and the answer depends on whether the circuit relied on the guaranteed minimums. If it did, the cheaper part is a downgrade that may pass bench test and fail on a cold lot. Where the J grade is short, the K grade in the same family is the safer move because it tightens the open loop gain rather than relaxing anything. The amplifier cross reference lists the BiFET families we supply, the pin to pin cross reference covers which types share this outline, and the lead time page shows what is available now.