Contact Us

LT1763IDE#TRPBF

Brand: Analog Devices
Analog Devices LT1763IDE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1763IDE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT1763IDE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1763IDE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1763IDE#TRPBF: the adjustable 500 mA low noise regulator in the industrial grade DFN, on reel

What this order code is

LT1763IDE#TRPBF is the adjustable member of the LT1763 family in the 12 lead 4 mm by 3 mm DFN with an exposed pad, in the industrial temperature grade, lead free and on tape and reel. The output is set by two external resistors against a 1.22 V reference, so any voltage from 1.22 V up to the input minus dropout is available, which is why one part number covers rails that the fixed versions cannot: 1.2 V, 2.8 V, 3.0 V, 4.2 V and the odd values that appear when a board is built around an existing transformer or battery pack. The regulator supplies 500 mA with 300 mV of dropout, draws 30 microamps, and drops below 1 microamp in shutdown.

The letters are not cosmetic. DE is the DFN, I is the industrial grade, TRPBF is the lead free finish on tape and reel, and the absence of a voltage digit is what makes it adjustable. A line that was built with a fixed 3.3 V part cannot be moved to this one without fitting two resistors, and a line that was built with this one cannot be moved to a fixed part without removing them and checking that the feedback node is not left floating.

Parameters as published

ItemValue
Output voltageadjustable, 1.22 V to 20 V
Reference1.22 V
Output current500 mA
Dropout at 500 mA300 mV
Input range1.8 V to 20 V
Quiescent current30 microamps, controlled in dropout
Shutdown currentunder 1 microamp
Output noise20 microvolts RMS with a 0.01 microfarad bypass capacitor
Minimum output capacitor3.3 microfarads
Protectionreverse battery, reverse current, current limit, thermal limit
Body12 lead DFN, 4 mm by 3 mm, 0.75 mm high
Temperature gradeindustrial
Packingtape and reel, lead free

Numbers that decide the application

The output is 1.22 V times one plus the ratio of the two resistors, so a 3.3 V rail needs a ratio of 1.705 and a 5 V rail needs 3.10. The divider current is the first decision: a 12.4 kilohm upper resistor sets 100 microamps, which is more than three times the 30 microamp quiescent current and therefore becomes the dominant term in the standby budget. Raising both resistors by a factor of ten brings the divider to 10 microamps and leaves the quiescent current dominant, at the cost of making the feedback node more sensitive to leakage and to noise pickup. Both choices are legitimate; what is not legitimate is a divider that carries less than a few microamps and a board that then wonders why the output sits high in a humid room.

The reference tolerance and the two resistors add directly. A pair of one percent resistors contributes plus or minus one percent to the ratio, and the reference contributes its own tolerance on top, so the output tolerance is never better than the resistor pair. That is the trade against the fixed versions, where the divider is inside the part and does not appear in the error budget. On a 1.2 V rail the 1.22 V reference is also the floor: the part cannot regulate below 1.22 V, and a 1.2 V setpoint is 20 mV under the reference, so it works only as long as the reference sits at the bottom of its window.

Thermal headroom is the same as the fixed part and needs the same arithmetic. From 3.3 V to 1.8 V at 500 mA dissipates 0.75 W, from 5 V to 3.3 V dissipates 0.85 W, and from 12 V to 3.3 V dissipates 4.35 W, which no DFN will pass. The 3.3 microfarad minimum output capacitor is a stability requirement rather than a ripple requirement, and it holds for ceramic, tantalum and aluminium, which means the part does not need the series resistance that older low dropout regulators demanded.

Where it fits and where it does not

It fits rails that are not one of the six fixed voltages, prototype and low volume boards where one part number has to cover several builds, and any analogue rail where 20 microvolts of noise and a 300 mV dropout matter. It does not fit a rail below 1.22 V, a board with no room for two resistors and a bypass capacitor, or a conversion that would dissipate more than about 1 W in the package. It also does not protect itself from a feedback node that is left open by a missing resistor, so the assembly drawing is part of the electrical specification on this code.

Supply and second source questions

The questions we get on this code are about the resistor values a customer has already committed to, the grade and the packing. The adjustable version is often specified as a drop in for a fixed part on the assumption that the output is programmed somewhere else, and that assumption is the one to check before shipping. The members that share the die and the ones that only look similar are listed on the power management cross reference page.

Sourcing notes and next step

We quote this code against the bill of materials and check the four fields that decide whether the line runs: the programmed output, the grade, the body and the reel. Where the exact code is short we will say so rather than substitute a fixed voltage part into a socket that has a live divider on it. Send the line items, quantities and required date through the BOM shortage recovery page, and where the rail is part of a cost review rather than a shortage, the component cost reduction page sets out where a regulator change is worth making and where it is not. The family list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty