AD679BRZ
Product Specifications
AD679BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD679BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD679: 14 Bits at 128 kSPS With the Reference and Clock Already Inside
The AD679 is a complete 14-bit sampling analog to digital converter that holds the sample and hold amplifier, the converter, a 5 V reference, the clock and a microprocessor compatible bus interface in one package. That completeness is the point: a 14-bit converter built from a separate SHA, reference and clock has three more error terms and three more things to get wrong at bring up. The part converts at 128 kSPS, keeps 78 dB of signal to noise plus distortion on the K, B and T grades, and takes a 10 V full-scale input in either unipolar or bipolar mode with 10 megohms of input impedance, so an unbuffered source can drive it directly.
Two reads over an 8-bit bus
The 14 data bits come out in two read operations, eight bits then six, left justified. That is what makes the part usable on an 8-bit bus at a time when 16-bit buses were expensive, and it is also the first thing to check when a board is brought up: a bus that reads 14 bits in one access will get the high byte followed by a byte shifted by two positions. Data format follows the input mode, straight binary in unipolar and twos complement in bipolar, so the same converter gives either a unipolar code or a signed code without a firmware change. Conversions start either from a microprocessor strobe or from an external clock that is asynchronous to the system clock, which is what allows the part to be clocked from the same source as the rest of a sampling system.
Values and grades
| Parameter | Value | Note |
|---|---|---|
| Resolution | 14 bits | Two reads, 8 plus 6, left justified |
| Throughput | 128 kSPS | Conversions initiated by strobe or external clock |
| Signal to noise plus distortion | 78 dB | K, B and T grades, specified and tested |
| Full power bandwidth | 1 MHz | Full linear bandwidth 500 kHz |
| Input range | 10 V unipolar or bipolar | 10 megohm input impedance |
| Supplies | Plus 5 V and plus or minus 12 V | 560 mW typical dissipation |
| Packages | 28-lead plastic DIP, 28-lead cerdip, 44-lead J-lead ceramic | MIL-STD-883 versions available |
| Grades | K, B and T specified for AC and DC | J, A and S specified for AC, DC shown as typical |
Grade choice is an accuracy decision, not a price decision
The K, B and T grades are tested for both the dynamic parameters and the DC ones, meaning integral nonlinearity, gain and offset carry guaranteed limits. The J, A and S grades are tested for the dynamic parameters only, and their DC numbers appear as typical values. In a signal processing chain that is fine, because the converter sits behind a filter and the absolute gain is calibrated in software. In a measurement or control loop it is not, because the DC limits are exactly what the loop depends on, and a typical value is not a limit. Reading the ordering guide before a build goes to a second source is worth more than the price difference between grades, since a J grade substituted for a K grade will pass incoming test at room temperature and drift at temperature extremes.
Why this part still appears in repair and legacy builds
The AD679 is pin compatible with the 12-bit, 200 kSPS AD678, which means an existing board built around the 12-bit part can take the 14-bit one without a change to the copper, and that is the usual reason the part is still bought. The same pinout also means a substitute has to be checked for both resolution and throughput, since the pin compatible family spans both. The recursive subranging architecture with error correction and flash converters is what delivers 14 bits at this rate in a bipolar process, and the laser trimmed thin film resistors are what hold the accuracy over temperature. Any source for this part should be asked for the full part number with grade and package, because the same base number covers plastic, cerdip and ceramic bodies with very different storage and screening histories.
Procurement and second source
The AD679 is a long life part with no active replacement, so stock comes from broker channels and from decommissioned equipment rather than from a distributor shelf. The ADC DAC cross reference covers the converters that share its bus behaviour, the obsolete part cross reference hub is the place to start when the exact grade is gone, and date code, packaging and electrical checks are set out in the incoming inspection plan.