Contact Us

AD628ARZ

Brand: Analog Devices
Analog Devices AD628ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD628ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD628ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD628ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD628ARZ: A Difference Amplifier Whose Gain Can Go Below One

The AD628ARZ is a high common mode voltage difference amplifier with a programmable gain, and the unusual part is the bottom of the range: the gain equation published in the data sheet is G equals 0.1 times the quantity 1 plus REXT1 over REXT2, and the guaranteed range runs from 0.11 to 100 V per volt. A gain below one is exactly what a high side shunt needs when the shunt voltage is tens of volts and the converter behind it accepts two and a half. The input pair is preceded by an internal divider that attenuates by ten before the difference stage, so a plus or minus 120 V common mode lands inside the amplifier's own supply window. The part runs from a single supply of 4.5 V to 36 V, which means the same device covers a 5 V logic rail system and a 24 V industrial bus.

Published values

ParameterValue
Gain equationG equals 0.1 times 1 plus REXT1 divided by REXT2
Gain range0.11 to 100 V per volt, guaranteed
Supply range4.5 V to 36 V, single supply
Common mode rejection75 dB minimum, dc to 500 Hz, gain of 1
Input structureInternal 100 k and 10 k divider, 10 to 1 attenuation ahead of the difference stage
Filter pinCFILT, sets the feedback pole with an external capacitor
Gain setting pinsREXT1 and REXT2, two external resistors
Applications in the data sheetHigh voltage current shunt sensing, power supply monitoring, motor control
Body8-lead surface mount, R suffix

Why attenuation before amplification is the safe order

A 48 V bus with a 1 milliohm shunt produces 48 mV at full load, and the amplifier has to survive a short circuit on that bus without a divider in front of it. Placing the ten to one divider first means the difference stage sees 4.8 V of common mode at the worst case, well inside a 5 V supplied amplifier's window, and the fault current path is a resistor rather than a semiconductor junction. The cost is noise: the divider attenuates the signal before the amplifier's own noise is added, so the input referred noise figure is set by the divider ratio. For a shunt signal that is already millivolts this is acceptable, and it is the reason this topology is standard in motor drive and battery management current sense circuits rather than in low level sensor work.

Setting a gain below one on purpose

With REXT1 open and REXT2 fitted the gain sits at its floor of 0.11, so a bus voltage of 40 V maps to 4.4 V and fits a 5 V converter, which is the supply monitoring case in the data sheet. Adding REXT1 raises the gain toward 100 for shunt work. Because the equation is a ratio, the absolute resistor values only have to be stable relative to each other, and the CFILT capacitor sets a pole that rolls off the switching noise of the bus without loading the source. Programs that need a defined bandwidth should pick CFILT from the published transimpedance curve rather than from a rule of thumb, because the pole moves with gain.

Grade and body questions when this part goes short

Only the A grade exists for most order codes in this family, so substitution usually means a different amplifier topology rather than a different grade. A high common mode difference amplifier can be replaced by an isolation amplifier when galvanic isolation is needed, by a current sense amplifier when the common mode stays under 80 V, or by an instrumentation amplifier plus a divider when accuracy matters more than common mode range. Each of those changes the error budget, so the comparison has to be done on the specification rather than on the pinout. The amplifier cross reference lists the difference amplifier families we supply, the pin to pin cross reference covers the footprint question, and the drop in replacement guide sets out the checks before a topology change is accepted.