AD627ARZ-R7AD627BRZ-R7
Product Specifications
AD627ARZ-R7AD627BRZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD627ARZ-R7AD627BRZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD627ARZ-R7 and AD627BRZ-R7: 85 uA of Instrumentation Amplifier, and the Grade Letter That Sets the Offset
This page covers two order codes of the same instrumentation amplifier: the AD627ARZ-R7 and the AD627BRZ-R7, both in the 8-lead SO package in tape and reel. The part is a micropower instrumentation amplifier that draws 85 uA maximum, runs from plus 2.2 V to plus or minus 18 V, sets gain from 5 to 1000 with one external resistor, swings its output rail to rail, and quotes 38 nV per root hertz of input referred noise at 1 kHz and a gain of 100. Gain error is 0.03 percent typical and gain drift 10 ppm per degree C typical on the A grade at a gain of 5, the bandwidth is 80 kHz at a gain of 5, and settling to 0.01 percent is 135 us for a 5 V step at that gain.
The two order codes differ in the grade letter, and that letter is the whole purchase decision: the B grade guarantees 125 uV of offset on a dual supply with 1 uV per degree C of drift, and the A grade guarantees 200 uV with 3 uV per degree C. The A is also the grade whose 77 dB common mode rejection is quoted, against 83 dB for the B.
Three microvolts per degree is 375 microvolts over the industrial range
On the A grade the drift of 3 uV per degree C over 125 degrees is 375 uV, which is 1.9 times the 200 uV offset the part is bought for at room temperature. The B grade drifts 125 uV over the same span, which matches its 125 uV offset. In both cases the worst case over temperature is roughly twice the room temperature offset, and a circuit that budgets the offset alone will be surprised at the top of the range. On a 16-bit converter over a 2 V span, where one bit is 30.5 uV, the A grade offset is 6.6 bits and its drift is 12.3 bits.
Common mode rejection tells the same story in the other direction. At 77 dB the A grade rejects a 10 V common mode to 1.41 mV referred to the input, and the B grade at 83 dB rejects it to 0.71 mV. At a gain of 5 that is 7.1 mV and 3.6 mV at the output, so the two grades differ by more than the offset difference when the common mode is large. A bridge with a 10 V common mode is where the grade letter pays for itself.
| Supply current | 85 uA maximum, 0.43 mW at 5 V, 2.55 mW at plus or minus 15 V |
| Supply range | Plus 2.2 V to plus or minus 18 V, single or dual |
| Gain | 5 with no resistor, up to 1000 with one external resistor |
| Offset, B grade | 125 uV maximum, 1 uV per degree C, 125 uV over 125 degrees |
| Offset, A grade | 200 uV maximum, 3 uV per degree C, 375 uV over 125 degrees |
| Rejection | 77 dB on the A grade and 83 dB on the B grade at a gain of 5, 1.41 mV and 0.71 mV for a 10 V common mode |
| Noise | 38 nV per root hertz at 1 kHz and a gain of 100, 2.40 uV rms over 4 kHz |
| Bandwidth | 80 kHz at a gain of 5, 4 kHz at a gain of 100 |
| Settling | 135 us to 0.01 percent for a 5 V step at a gain of 5 |
| Packages | 8-lead SO on both order codes |
Eighty kilohertz at a gain of 5 is four at a gain of 100
The bandwidth falls as the gain rises, which is normal for a three amplifier instrumentation stage, and the closed loop bandwidth at a gain of 100 is 4 kHz. Integrating 38 nV per root hertz over 4 kHz gives 2.40 uV rms of input referred noise, which at a gain of 100 is 240 uV at the output, or 7.9 bits on a 2 V span. That is the noise floor of a high gain stage and it is why the part is used at moderate gains where its 85 uA matters more than its bandwidth.
The 135 us settling is slow, and it is slow in a way that matters for a multiplexed input: a channel change that has to settle to 0.01 percent takes 135 us, which is 7.4 kSPS per channel in a system that multiplexes. A board that expects 100 kSPS from this amplifier is expecting 30 times what the settling allows, and the symptom is channel to channel crosstalk that looks like a multiplexer problem.
Two questions buyers ask
Which grade should be bought?
The B grade when the input is a bridge or a thermocouple with a large common mode and a wide temperature range, because the drift and the rejection are both twice as good. The A grade when the signal is large, the temperature is controlled, or the offset is trimmed in production. The two are pin compatible and electrically similar, so the difference is only visible in the error budget and the price.
Can it run from a single 3 V rail?
Yes, the minimum is 2.2 V, and the rail to rail output is what makes a 3 V single supply usable: the output can swing close to both rails, so the dynamic range is nearly the full supply. What does not change is the input common mode range, which is limited by the input stage and has to include the signal in a single supply arrangement, so a signal near ground needs either a negative supply or a rail to rail input stage that this part does not have.
Ordering and supply
The ARZ and BRZ suffixes are the 8-lead SO package in tape and reel with the A and B grades respectively. Substitution traps are the grade letter and the gain resistor: a B grade in an A grade socket is an upgrade, the reverse is a downgrade that shows up as drift, and a part with the same 85 uA but a different gain equation needs a different resistor for the same gain.
We hold and source both grades for production and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a substitute has to be proven in an existing instrument, the order in how to verify a drop in replacement starts with the grade and the gain resistor.
Request Quote — In Stock, 100% New & Original, Full Warranty