AD620ARZ
Product Specifications
AD620ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD620ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD620ARZ: Gain of 1 to 10,000 From One Resistor and 1.3 mA of Supply
The AD620ARZ is the A grade of a three op amp instrumentation amplifier in the 8-lead surface mount body, and the number that sells it is 1.3 mA maximum supply current against a gain range of 1 to 10,000 set by a single resistor. The gain equation is G equals 1 plus 49.4 k divided by RG, so the resistor for a gain of 100 is 499 ohm and for a gain of 1000 it is 49.4 ohm, both ordinary E96 values. Offset for the B grade is 50 microvolts maximum, input bias current is 1.0 nA maximum, input voltage noise is 9 nV per root hertz at 1 kHz, and the 0.1 Hz to 10 Hz noise is 0.28 microvolts peak to peak. Common mode rejection is 100 dB minimum at a gain of 10, and the part settles to 0.01 percent in 15 microseconds, which is what makes it usable in front of a multiplexed converter.
Published values
| Parameter | Value |
|---|---|
| Gain equation | G equals 1 plus 49.4 k divided by RG |
| Gain range | 1 to 10,000 |
| Supply current | 1.3 mA maximum |
| Input offset, B grade | 50 microvolts maximum |
| Input bias current | 1.0 nA maximum |
| Voltage noise | 9 nV per root hertz at 1 kHz |
| Low frequency noise | 0.28 microvolts peak to peak, 0.1 Hz to 10 Hz |
| Current noise | 0.1 pA per root hertz |
| Common mode rejection | 100 dB minimum at a gain of 10 |
| Nonlinearity | 40 ppm maximum |
| Bandwidth | 120 kHz at a gain of 100 |
| Settling | 15 microseconds to 0.01 percent |
The Superbeta input stage and what it does to bias current
The input devices are Superbeta transistors, which is how a bipolar input amplifier reaches 1.0 nA of bias current without the drift behaviour of a JFET stage. At that level the current noise through a 10 k source is negligible, so the part works with high impedance bridges and with thermocouples whose source resistance moves with temperature. The same choice costs bias current drift, and the data sheet states it per grade, so a channel that has to hold offset over temperature should be selected on drift rather than on the room temperature offset figure.
Single resistor gain and the error it brings
The internal resistors are trimmed to a ratio and the external RG sets the absolute gain, so the gain error at high gain is dominated by the external resistor tolerance rather than by the amplifier. A 1 percent RG at a gain of 1000 gives roughly 1 percent gain error, far worse than the amplifier itself. Programs that need accurate high gain should specify a 0.1 percent resistor or trim the gain against a known input. The other consequence is that RG has to be connected with short traces and no shared return, because the internal feedback network senses the voltage across RG and any drop in that path appears as gain error.
Where this part still wins, and what replaces it
The AD620 is no longer the lowest noise in-amp in the catalogue and no longer the cheapest, but it is still the part with the widest published gain range in an 8-lead body and a supply current under 1.5 mA. For battery powered instruments, weigh scale front ends and ECG preamplifiers it remains a reasonable first choice. Where a newer device is wanted, the upgrade table in the data sheet points at parts with better specifications, and the footprint differs, so the swap is a board revision rather than a second source. The amplifier cross reference lists the in-amp families we supply, the medical device components page covers the ECG and patient monitor cases, and the drop in replacement guide sets out what has to be checked before a body change is accepted.