AD5544ACPZ-1-RL7
Product Specifications
AD5544ACPZ-1-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5544ACPZ-1-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD5544ACPZ-1-RL7: Four 16 Bit Current Output DACs That Settle in 0.9 Microseconds
The AD5544ACPZ-1-RL7 is a quad 16-bit current output digital to analogue converter. Linearity is plus or minus 1 LSB on the B grade, the full scale current is 2 mA plus or minus 20 percent with a plus or minus 10 V reference, settling to plus or minus 0.1 percent takes 0.9 microseconds, multiplying bandwidth is 12 MHz, and midscale glitch is minus 1 nanovolt second. Each of the four channels has its own four quadrant multiplying reference input and its own feedback resistor, so each can be used with a different reference or with an ac signal. Supply range is 2.7 V to 5.5 V. The interface is a three wire SPI with a serial data output for daisy chaining, a load DAC strobe for simultaneous update of all four outputs, an internal power on reset to zero, and an MSB pin that selects whether a reset forces zero code or half scale. The -1 order code is the 32-lead LFCSP.
A current output converter is chosen when the output stage has to be an operational amplifier the board controls. The converter sets the current, the amplifier turns it into a voltage, and the two together set the settling, the noise and the offset. That is one more part than a voltage output converter and one more degree of freedom.
One LSB is 30.5 nanoamps, which is why the amplifier matters
At 16 bits and a 2 mA full scale, one LSB is 30.5 nA, which is 0.0015 percent of full scale. An operational amplifier with 2 microvolts of offset in the current to voltage stage adds an error at the output, and the resistor that sets the gain converts the current error into a voltage error. The linearity specification of plus or minus 1 LSB describes the converter and not the amplifier, so a system that quotes 16 bit accuracy is quoting two parts and a resistor network.
The feedback resistor inside the package tracks the converter over temperature, which is what allows a voltage output to be built without a separate precision resistor. The tracking is a ratio and not an absolute value, so the absolute gain still depends on the external amplifier and on the reference.
Twelve megahertz of multiplying bandwidth against 1.11 MHz of settling
Settling of 0.9 microseconds to plus or minus 0.1 percent corresponds to about 1.11 MHz if it were a single pole response, and the multiplying bandwidth is 12 MHz. The two are not the same measurement: the bandwidth describes a small signal response around an operating point, and the settling describes a full scale step. A system that uses the converter as a multiplying element with an ac reference at 1 MHz is working at the top of the large signal range, and one that updates a dc set point only cares about the 0.9 microseconds.
Midscale glitch of minus 1 nanovolt second is the charge that reaches the output when the converter crosses its major carry. On a 16-bit part the midscale transition is where all the bits change, and the glitch is the reason the output amplifier has to recover quickly rather than only settle accurately.
The load DAC strobe is what makes four channels useful together
The interface loads each channel into an input register and then a single strobe updates all four outputs at once. Without it, four channels would update one after another and the outputs would be skewed by the time it takes to write four words. In a system that drives four phases of a calibration or four axes of a deflection coil, the simultaneous update is the feature that keeps the outputs aligned.
The MSB pin selects the reset state: zero code or half scale. That is a board decision, not a software one, and it decides what the outputs do at power up before the first word is written.
| Function | Quad 16-bit current output DAC with four multiplying reference inputs |
| Linearity | Plus or minus 1 LSB on the B grade, 16-bit resolution on all four channels |
| Full scale | 2 mA plus or minus 20 percent with a plus or minus 10 V reference |
| Resolution | 1 LSB is 30.5 nA or 0.0015 percent of full scale |
| Settling | 0.9 microseconds to plus or minus 0.1 percent, about 1.11 MHz equivalent |
| Bandwidth | 12 MHz multiplying, a small signal figure |
| Glitch | Minus 1 nanovolt second at midscale |
| Interface | Three wire SPI with data out for daisy chain and a load strobe for simultaneous update |
| Reset | Power on reset to zero, MSB pin selects zero or half scale on reset |
| Body and supply | 32-lead LFCSP, 2.7 V to 5.5 V |
Two questions buyers ask
Can the outputs be updated one at a time?
Yes. Each channel has its own input register, and the load strobe decides when they all move. A system that wants one channel at a time simply asserts the strobe after each write, and a system that wants all four together writes four words and then strobes once.
Is the 12 MHz bandwidth the update rate?
No. The bandwidth is a small signal figure for a multiplying application, and the update rate is set by the settling time of about 0.9 microseconds per full scale step, which is roughly 1.11 MHz. A system that updates at 12 MHz is working outside the large signal settling specification.
Ordering and supply
The ACPZ suffix is the 32-lead LFCSP and RL7 is tape and reel. The -EP version of this converter is a separate order code screened for defence and aerospace work, with a military temperature range and a controlled baseline, and it is not a commercial part with a wider grade stamp on it.
We hold this converter for instrumentation and test builds. Start at the analog mixed signal ICs family page, the ADC and DAC cross reference page is where a converter is matched to the amplifier behind it, and medical device components covers the documentation a medical instrument has to carry for an analogue front end.
Request Quote — In Stock, 100% New & Original, Full Warranty