AD5300BRMZ
Product Specifications
AD5300BRMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5300BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD5300BRMZ: An 8-Bit DAC That Draws 115 uA and Fits an MSOP
The AD5300BRMZ is a single channel 8 bit voltage output converter in an 8-lead MSOP, and the two numbers that define it are 115 uA of supply current at 3 V and a power down state that draws 200 nA at 5 V. The reference is derived from the supply, so there is no external reference pin to decouple and no reference buffer to pay for, and the output amplifier swings rail to rail with a 1 V per microsecond slew rate. On a 3 V supply the whole part consumes about 0.35 mW, which is why it appears in portable instruments, programmable current sources and digital gain and offset adjustment. The 6-lead SOT-23 version is the same die in a smaller body.
Published values
| Parameter | Value |
|---|---|
| Resolution | 8 bits, single channel |
| Supply | 2.7 V to 5.5 V |
| Supply current | 115 uA at 3 V, 140 uA maximum |
| Power down current | 200 nA at 5 V, 50 nA at 3 V |
| Reference | Derived from the supply |
| Output | Rail to rail buffered, 1 V per microsecond |
| Monotonicity | Guaranteed monotonic |
| Power on reset | Output to 0 V |
| Interface | Serial, Schmitt trigger inputs, SYNC interrupt |
| Bodies | 8-lead MSOP and 6-lead SOT-23 |
A supply referenced DAC is a ratiometric DAC
With the reference taken from the supply, the output is a fraction of the supply voltage rather than an absolute value. That is exactly right in a ratiometric system, where the sensor and the converter share the same rail and the ratio cancels, and it is exactly wrong where the output has to be an absolute voltage that does not move when the rail does. In a 3 V system with a one percent rail tolerance the full scale moves by one percent, which is 2.5 counts at 8 bits, so the error is small enough to be absorbed. In a 12 bit part the same one percent becomes 41 counts, which is why the supply referenced approach suits the 8 bit member of the family better than the higher resolution ones.
Guaranteed monotonic at 8 bits is the useful guarantee
At 8 bits the step size is about 12 mV on a 3 V rail, and a converter that is monotonic is guaranteed to move in the right direction at every code, which matters in a control loop that hunts for a set point. A part that is only monotonic to 7 bits can stall or reverse at a major carry, and the loop then oscillates around the set point by one or two counts. Cheap converters often specify monotonicity only at 25 degrees; checking whether the guarantee holds over the temperature range is worth the line in the data sheet, because the loop behaviour at temperature is what the field sees.
Power down, power on reset and the safe start
The part comes up with the output at zero volts, which is the safe state for a bias control and the wrong state for a loop that expects midscale. Three power down functions are available, drawing between 50 nA and 200 nA depending on the supply, and each returns the output to a defined state rather than leaving it floating. In a battery instrument that samples periodically, the difference between 115 uA running and 200 nA parked is the difference between days and months of standby, so the firmware should park the converter between measurements rather than leave it at a code.
Where an 8 bit DAC is enough
An 8 bit converter is enough for a set point that only needs one percent accuracy, for a contrast or brightness control, for a coarse gain step in front of a fine trim, or for a bias that is trimmed by a separate loop. It is not enough for a 12 bit measurement chain, where the converter's own quantisation would be visible. The family is pin compatible across 8, 10 and 12 bits, so a board can be reworked to a higher resolution part without a new board, which is a useful property when a product line spans several accuracy classes. The converter cross reference page groups the parts we hold by resolution and body, the pin to pin cross reference page lists the family members that swap directly, and the lead time page shows what is on the shelf across the family.