Contact Us
  • Home
  • COMPONENTS
  • Solid State Relays and Photovoltaic MOSFET Drivers

Solid State Relays and Photovoltaic MOSFET Drivers

Photovoltaic MOSFET drivers and 1 Form A solid state relays from 40 V to 400 V, with on resistance, isolation and switching time listed for each part.
quote now

Product Specifications

Solid state relays and photovoltaic MOSFET drivers

Product Overview

A solid state relay replaces a coil, an armature and a set of contacts with an LED, a photovoltaic array and a pair of MOSFETs. Nothing moves, so there is no contact bounce, no arc at the moment of opening and no wear that follows the number of operations. The price is on resistance: a mechanical contact closes at a few milliohms, while a 60 V photo MOSFET relay closes at 0.8 ohm to 16 ohm depending on the die area. For a signal path or a small load that is a good trade, and for a 2 A load it is still workable if the package can pass the heat.

The second family on this page solves the drive side rather than the load side. A photovoltaic driver converts LED current into a small isolated voltage around 8 V, which is enough to lift the gate of an external power MOSFET. That removes the auxiliary bias supply that a high side switch would otherwise need, and it keeps the gate drive galvanically separate from the control side. The trade is speed: a photovoltaic array charges the gate slowly, so the VOM1271 reaches a 200 pF load in about 53 µs and switches off in 24 µs through its internal discharge circuit.

Selection starts from the load, not from the package. A 48 V signal loop with 100 mA needs a 60 V part with a low off state leakage, because a leakage of 1 µA into a high impedance input is already an error. A 230 V AC load needs a part rated at 400 V peak and a package with enough creepage for the pollution degree of the enclosure. A relay that switches a transformer primary needs the zero crossing behaviour stated, and one that switches a DC load with inductance needs a clamp across the output. Every row below gives the load voltage, the continuous current at the stated case, the on resistance and the isolation voltage the maker publishes.

Key Specifications

ParameterSignal level relayPower relayPhotovoltaic driver
Load voltage40 V to 60 V60 V to 400 V peakdrives an external MOSFET rated for the bus
Continuous load current0.1 A to 0.5 A0.12 A to 2.0 Aset by the external MOSFET
On resistance0.83 ohm to 16 ohm0.09 ohm to 16 ohmnot applicable
Input drive1 mA to 5 mA LED current3 mA to 5 mA LED current10 mA LED current for 8.4 V open circuit
Isolation voltage1500 Vrms3750 Vrms to 5000 Vrms3750 Vrms and above
Switching time0.65 ms on, 0.08 ms off on AQY212S5 ms on, 1 ms off on TLP241A53 us on, 24 us off into 200 pF
Off state leakage1 uA1 uAnot applicable
Usual packageSOP4, SO4DIP4, DIP6, SOP8, 6-SMDSOP4

Included Models and Order Codes

The rows below are the order codes quoted most often for signal switching, mains side switching and high side gate drive. State the load voltage including the transient, the continuous current, the ambient temperature inside the enclosure and whether the load is AC or DC, and the part, the series resistor and the clamp are confirmed together.

Part NumberTypeLoad VoltageLoad CurrentOn Resistance or DrivePackage
AQY212S1 Form A PhotoMOS60 V0.5 A0.83 ohm typ, 2.5 ohm maxSOP4
AQY221N2S1 Form A, low terminal capacitance40 V0.12 A9.5 ohm typ, 12.5 ohm maxSOP4
AQV212AX1 Form A, six pin60 V0.55 A0.83 ohm typ, 2.5 ohm max6-SMD
AQW254AZ2 Form A400 V0.12 A10.2 ohm typ, 16 ohm max8-SMD
TLP241A1 Form A photorelay40 V2.0 A0.09 ohm typ, 0.15 ohm max continuousDIP4
TLP241AF1 Form A, 10.16 mm pitch40 V2.0 A0.09 ohm typ, 0.15 ohm max continuousDIP4
CPC1017N1 Form A OptoMOS60 V0.1 A16 ohm max, 1 mA driveSOP4
ASSR-12181 Form A photo MOSFET60 V0.2 A10 ohm max, 3 mA driveSO4
ASSR-12191 Form A, DC only connection60 V0.4 A2.5 ohmDIP6
G3VM-61A1MOS FET relay, analog switching60 V0.5 A2 ohm maxDIP4
VOM1271Photovoltaic MOSFET driverexternal switch15 uA short circuit8.4 V open circuit at 10 mASOP4

Key Features

No contact wear – the switch is a pair of MOSFETs, so the number of operations is limited by the LED rather than by an arc, and there is no contact bounce to debounce in firmware.

Isolation stated at the part – 1500 Vrms on the small SOP parts and 3750 Vrms to 5000 Vrms on the DIP photorelays, which is what decides whether a mains side load can share a board with a logic side connector.

Low drive current – the CPC1017N closes with 1 mA and the ASSR-1218 with 3 mA, so a relay can be driven from a microcontroller pin through a resistor instead of a transistor stage.

Bidirectional output – a photo MOSFET conducts in both directions, which is why the same part switches an AC signal and a DC signal without a bridge in front of it.

Bounce free analog switching – the G3VM-61A1 and the AQY221N2S are used for signal routing because the on resistance is flat over the signal range and the off capacitance is a few picofarads.

Photovoltaic gate drive without a bias rail – the VOM1271 takes its energy from the LED current and returns 8.4 V open circuit, so a high side MOSFET can be driven with two wires across the isolation barrier.

Thermal limit stated at the case – the 2 A rating of the TLP241A belongs to a case held at 25 C, and the on resistance is given both for a 1 s pulse and for continuous operation, so a 2 A load in a warm enclosure is checked against the continuous figure.

Clamp and series resistor quoted with the part – an inductive DC load needs a diode or a transient suppressor across it, and the LED needs a series resistor set for the drive current, both of which are quoted on the same line as the relay.

Applications

These parts are quoted for boards that switch a load without a coil, typically where: The relay and its driver sit on the same control board, so they are quoted with the SUPERB PCB and the SUPERB PCBA build for that board.

Test and measurement switching – a scanner that routes a thermocouple or a shunt signal through 32 channels needs a switch with a flat on resistance and a leakage below 1 uA, which is the reason the small SOP photo MOSFET relays are used in instrument multiplexers.

Mains side control in appliances – a 230 V heater or a fan in a smart meter or a commercial appliance is switched by a 400 V part with 3750 Vrms isolation, and the zero crossing behaviour of the load decides whether a random turn on part is acceptable.

Medical and patient connected equipment – a relay that separates a patient connected circuit from the mains side has to hold the isolation voltage of the whole barrier, so the 5000 Vrms DIP photorelays are used where reinforced insulation is required.

Battery and solar disconnect – a photovoltaic driver lifts the gate of a back to back MOSFET pair in the negative or positive rail, which gives a disconnect with no coil current and no holding power once the LED is off.

Sourcing and Cross-Reference

Replacing a mechanical relay is a board change, not a part swap. The footprint, the coil drive, the contact rating and the leakage all move at once, so a cross reference has to start from the load voltage and the isolation requirement. A 12 V coil relay that switched 2 A at 250 V AC is not replaced by a 60 V photo MOSFET relay, even if both are 4-pin devices with the same pin count.

The second check is thermal. On resistance rises with junction temperature, and a part quoted at 0.83 ohm at 25 C is closer to 1.3 ohm in a 70 C enclosure. Two relays side by side on a dense board also heat each other, so the derating curve in the data sheet is the number to use, not the single value on the first page.

Lead time on photorelays follows the optocoupler line, and a part that is in stock this month can move to eight weeks without notice. The quotation line therefore states the batch date and the quantity behind it, and for a long life build the driver and the relay are qualified as a pair so that a substitution does not reopen the isolation test.

For volume builds, SUPERB Assembly support covers the LED series resistor value, the creepage check under the part and the reflow profile the SOP and DIP packages need.

Q: Can you supply a pin compatible replacement when a photorelay or a photovoltaic driver is discontinued?

A: Yes. Send the current part number, the load voltage, the load current, the ambient temperature and the isolation class, and the SUPERB Tech sales team will confirm the order code and the nearest part that holds the same footprint and isolation rating.

Why Buyers Source Relays and Drivers Through SUPERB

  1. Load and isolation checked first: the cross reference starts from the voltage across the switch and the barrier class, so a substitute never arrives with a lower isolation rating than the barrier it has to hold.
  2. On resistance at temperature: the quotation gives the on resistance at the case temperature of the enclosure, which is the figure that decides whether a 0.5 A load needs a second package.
  3. Driver and switch as one line: the photovoltaic driver, the external MOSFET and the clamp are quoted together, so the gate charge and the turn off path are matched before the board is built.
  4. Status tracked on the part: parts under an end of life notice are flagged with the nearest equivalent that keeps the footprint, before an instrument line runs out of a relay it qualified years ago.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and power semiconductors, LED indicators and optocouplers, Digital isolators, Load switches and hot swap controllers, Pin to pin cross reference.