Contact Us
  • Home
  • COMPONENTS
  • Conductivity Cells and Toroidal Sensors for Water Analysers

Conductivity Cells and Toroidal Sensors for Water Analysers

A conductivity reading is only as good as the cell constant, and the cell constant is the number that changes when the electrodes foul or the cable is extended. The parts below cover graphite and stainless steel contacting cells from k 0.1 to k 10, and toroidal sensors that reach 2000 mS/cm without any metal touching the sample. Each entry gives cell constant, wetted material, temperature and pressure limits and the fitting, so a cell is chosen for the range and for the pipe it goes into. Temperature compensation is listed with the element type, because a 10 k thermistor and a Pt1000 do not answer the same way at the top of the range.
quote now

Product Specifications

Product Overview

Conductivity is measured by putting a voltage across two electrodes and reading the current, so the geometry of those electrodes is part of the answer. That geometry is folded into one number, the cell constant, and every reading is the measured conductance multiplied by it. A cell with k = 0.1 is built for pure water, a cell with k = 1.0 covers drinking water and general process lines, and a cell with k = 10 belongs on brine or on a concentrated acid line where the conductance is high and the resistance is low.

The practical limit of a contacting cell is fouling. Graphite is cheap and good enough for clean water, but a graphite cell in a stream carrying oil or scale reads low and keeps reading low until it is cleaned. Stainless steel with a PEEK insulator survives higher temperature and pressure, and the 316 body can be removed and cleaned without breaking. Neither of them works in a stream that coats everything, and that is where a toroidal sensor comes in.

A toroidal sensor has no electrodes in contact with the liquid. Two coils sit inside a moulded body, one drives a current loop through the liquid and the other reads it, so the only thing in the sample is the body material. That construction is why a toroidal sensor reaches 2000 mS/cm and why it keeps working in slurry, brine and caustic where a contacting cell would polarise or plug. The price is a nominal cell constant with a wider tolerance, so the sensor is calibrated in the loop rather than trusted from the label.

Temperature compensation is not an accessory on this measurement, it is part of the reading. Conductivity rises about 2 percent per degree C for most aqueous solutions, so a 10 C error in the temperature element shows up as a 20 percent error in the displayed value. Pt100 and Pt1000 elements are the stable choices, a 10 k thermistor is the common one on light duty sensors, and the transmitter has to be set to the element that is actually fitted.

Key Specifications

ParameterValueNote
Cell constantsk 0.1, k 1.0 and k 10 per cmk 0.1 for pure water, k 1.0 for general process, k 10 for brine and concentrated acids
Cell constant toleranceplus or minus 10 percent on a graphite cellthe label value is nominal until the cell is checked in a standard solution
Measuring range, contacting0 to 20 mS/cm on k 0.1, up to 200 mS/cm on k 10the practical range follows the cell constant, not the transmitter
Measuring range, toroidal0 to 2000 mS/cm (2 S/cm)the reason a toroidal sensor is used on brine and caustic
Wetted materialsgraphite with epoxy, 316 stainless steel with PEEK, glass filled PEEK, glass filled Tefzelthe body decides which reagents the sensor can see
Temperature range0 to 70 C on graphite, 0 to 100 C on the stainless family, 0 to 250 C on the high temperature stainless versioneach rating is paired with its own pressure figure
Pressure100 psig on graphite, 200 psig at 100 C on the stainless family, 250 psig at 200 C, 600 psig at 250 Cthe highest ratings apply to one option only
Temperature elementPt1000, Pt100 or 10 k thermistorthe thermistor option caps the temperature rating at 70 C
Temperature compensationabout 2 percent per degree C for aqueous solutionsa wrong element type looks like a wrong cell constant
Fittings1/2 inch MNPT, 3/4 inch MNPT, 12 mm gland, flange and sanitary optionsthe fitting and the insertion length are ordered together
Cabletwo wire without compensation, four wire with a temperature elementthe fourth wire is the element, not a spare
Response time0.5 s on the inductive familya slow response on a contacting cell usually means fouling
Flow limit3 m/s maximum on the inductive familyhigher flow erodes the body and shifts the reading

Included Models and Order Codes

The contacting cells come first because they cover most water lines, and the toroidal sensors come after because they answer a different problem. A graphite cell with k = 0.1 and a stainless cell with k = 10 are the two ends of the same family: the first is for water that is almost an insulator, the second for a line that is almost a conductor. The toroidal parts are listed with the range they are built for, because a nominal cell constant of this type carries a wider tolerance and the loop calibration is what makes the number trustworthy.

PartTypeCell constantRangeTemperaturePressureNote
CS150 K=0.1contacting, graphite, 12 mm0.1 per cmlow range water0 to 70 C100 psigminimum immersion 53 mm, epoxy body
CS150 K=1.0contacting, graphite, 12 mm1.0 per cmgeneral water0 to 70 C100 psigminimum immersion 12.7 mm
CS650TCcontacting, 316 stainless, 1/2 inch NPT0.1 or 1.0 per cmpure water and general0 to 100 C200 psigPEEK insulator, aflas O-rings
CS675TCcontacting, 316 stainless, 3/4 inch NPT0.1, 1.0 or 10 per cmgeneral to brine0 to 100 C250 psigwith temperature element, PVC jacketed four wire cable
CS675HTTCcontacting, 316 stainless, high temperature0.1, 1.0 or 10 per cmboiler and hot process0 to 200 C250 psigPTFE coated leads, no PVC jacket
CS675HPTCcontacting, 316 stainless, high pressure0.1, 1.0 or 10 per cmhigh pressure lines0 to 100 C300 psigextended insertion length available
CS676HTTCcontacting, 316 stainless, extended length0.1, 1.0 or 10 per cmboiler and deep tee0 to 200 C250 psiglonger body for a thick pipe wall
Rosemount 228, PEEKtoroidal, flow through2.7 per cm nominalup to 2000 mS/cmup to 200 C on the high temperature optionup to 295 psig on the high temperature optionglass filled PEEK body, Pt100 inside, 20 ft cable
Rosemount 228, Tefzeltoroidal, flow through2.7 per cm nominalup to 2000 mS/cmstandard rangestandard rangeTefzel body for oxidising reagents
Hach 3700, PEEKinductive, convertible mountnot quoted as a fixed value0 to 2000 mS/cmprocess range of the bodyprocess range of the bodyaccuracy 0.01 percent of reading, response 0.5 s, flow limit 3 m/s

Choosing the Cell Constant Before the Sensor

The cell constant is chosen from the conductivity the line is expected to run at, and the choice is made before the body material and the fitting. The table is the short version of that decision, with the error that shows up when the wrong constant is used.

Expected conductivityCell to useWhyWhat goes wrong otherwise
Below 10 microsiemens per cm, pure and ultrapure waterk 0.1 contacting cellthe resistance is high, so a small constant keeps the signal readablea k 1.0 cell reads near zero and the noise dominates
10 microsiemens to 20 millisiemens per cmk 1.0 contacting cellthe middle of the range for drinking water and general processa k 0.1 cell polarises and drifts
Above 20 millisiemens per cm, brine and concentrated acidk 10 contacting cell or a toroidal sensorthe resistance is low, so a large constant keeps the current in rangea k 1.0 cell saturates the transmitter
Slurry, caustic, oil bearing or scaling streamstoroidal sensornothing metal touches the sample, so there is nothing to coata contacting cell reads low within days and cannot be cleaned in place
Line above 100 Cstainless cell with the matching rating, or a toroidal body rated for itthe ratings are paired, temperature with pressurethe O-ring and the insulator are the parts that fail first

Key Features

Cell constants from 0.1 to 10 – one family covers pure water, drinking water and brine, so the range is answered by the constant rather than by a different sensor type

Graphite for cost, stainless for duty – graphite cells suit clean water, and 316 stainless with a PEEK insulator carries the temperature and pressure

Toroidal body with no electrodes – two coils read the current loop through the liquid, so slurry and caustic do not foul a measuring surface

Pt1000, Pt100 or 10 k element – compensation is ordered with the cell, and the transmitter is set to the element actually fitted

Paired temperature and pressure ratings – the 200 C version is rated at 250 psig and the 250 C version at 600 psig, and the two are never separated

Standard pipe fittings – 1/2 and 3/4 inch NPT plus 12 mm glands, so the cell goes into the tee the line already has

Four wire cable with compensation – the element has its own pair, which keeps the temperature reading out of the conductivity loop

Insertion length options – standard and extended bodies for thick pipe walls and for a tee that sits deep in insulation

Applications

Conductivity cells sit on water treatment, on rinse stages and on concentration control. The three cases below are where the specification is decided.

Water treatment and reverse osmosis – feed, permeate and concentrate conductivity on a skid. Permeate runs at a few microsiemens and needs a k 0.1 cell, while the concentrate needs a k 10 cell or a toroidal sensor, and the two are rarely the same part.

Boiler and cooling water – conductivity as a blowdown control. The stainless family with a high temperature rating is the one for a sample that leaves the boiler hot, and the 200 C option exists for exactly that line.

Brine, caustic and chemical concentration – acid, base and salt concentration read through conductivity. A toroidal sensor is used here because the metal electrodes of a contacting cell would polarise, and because the body survives the reagent that the line carries.

The analyser boards behind these sensors are the kind of build SUPERB PCB and SUPERB PCBA programmes cover, from the electrode input to the isolated current loop.

Sourcing and Cross-Reference

Cell constant, temperature element and cable length are three separate choices on the same order, and a sensor that arrives with the wrong element is a sensor that reads wrong until the transmitter is reprogrammed. We take the three together and quote them as one line.

For a line that is already running, the old cell constant and the old fitting matter more than the brand. A k 1.0 cell with a 3/4 inch thread can be replaced by a different body only if the thread and the insertion depth match, and we check that before naming a part.

Toroidal sensors are the ones that go obsolete quietly, because the transmitter and the sensor are often a pair. Where the sensor is no longer listed, we cross reference the body material and the cell constant against a current part and say plainly when the transmitter also has to change.

A sensor, its cable and the gland are ordered as one set when a line is down, which is how SUPERB Assembly ships a replacement.

Q: Can you supply a conductivity cell with the same cell constant and thread as the one already on the line?

A: SUPERB Tech can confirm the cell constant, the thread and the temperature element against the old part before an order is released.

Why Buy Conductivity Cells from SUPERB

  1. Cell constant and fitting quoted together: the constant, the thread and the insertion length are confirmed before a part is named, so the replacement drops into the existing tee
  2. Range checked against the process: we ask for the expected conductivity before recommending k 0.1, k 1.0, k 10 or a toroidal body
  3. Temperature element matched to the transmitter: Pt1000, Pt100 and 10 k thermistors are not interchangeable, and the cable is ordered with the element the transmitter expects
  4. Toroidal options for dirty streams: slurry, caustic and brine are answered with a body that has no metal in contact with the sample
  5. Paired ratings stated plainly: temperature and pressure are quoted as one rating per part number, not as two separate maxima

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Water Quality Sensor Circuits for pH, Conductivity and Dissolved Oxygen, pH and ORP Electrodes for Process Analysers, Liquid Flow Sensors for Medical and Analytical Instruments, Level Sensors and Float Switches for Tanks and Sumps, Turbidity and Photometric Detector Modules for Water Analysis, Sensors and Detectors, Component Lead Time Solutions.