TPS77618DR
Product Specifications
TPS77618DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS77618DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS77618DR 500 mA 1.8 V regulator with a power good flag
The TPS77618DR is the 1.8 V fixed member of the TPS776 family in the eight pin SOIC body. It is the same 500 mA regulator as the TPS775, with the same 169 mV of typical dropout on the 3.3 V point, the same 85 microamp of quiescent current and the same 2 per cent tolerance, but the flag pin carries a power good output instead of a reset. That difference decides the application: a power good flag tells the system that the rail is up, a reset holds a processor down until it is, and the two are not interchangeable on one net.
The flag is open drain, so it needs a pull up and it can be tied together with the flags from other rails to make a single good signal. Because the comparator watches the output rather than the input, the flag stays low during a brown out until the rail has actually collapsed, which is the behaviour a sequencing state machine wants. The output is stable with a 10 microfarad low ESR capacitor, and the current limit sits between 1.2 A and 1.9 A, which lets the part charge a large ceramic bank at start up without folding back before the rail is up.
Key parameters printed in the SLVS232J document
| Output | 1.8 V fixed, fixed members from 1.5 V to 3.3 V in the family |
| Load current | 500 mA |
| Dropout | 169 mV typical at 500 mA on the 3.3 V member of the family |
| Accuracy | 2 per cent over the specified conditions |
| Quiescent current | 85 microamp typical across the load range |
| Current limit | 1.2 A typical, 1.6 A maximum, 1.9 A at the top of the band |
| Rejection | 60 dB at 1 kHz with a 10 microfarad output capacitor |
| Flag | Open drain power good, released when the output is inside tolerance |
Package, reel and top side marking
| Package | SOIC, D body, eight pins |
| Reel | 2500 pieces on a large tape and reel for the DR row; the addendum prints the DR line against a 75 piece tube, so the quantity has to be matched to the code |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 125 degrees, top side marking 77618 |
Where a flag beats a reset
This member belongs on a board that already has a sequencer or a microcontroller deciding when rails come up. The controller enables the regulator and then waits on the flag, so it does not have to model the regulator's own timing; that is the difference from the reset version, where the regulator decides. On a 1.8 V rail feeding an FPGA input output bank, the flag also gives the controller a way to keep the bank off until the core is up, which is the ordering that keeps a device from driving into an unpowered bank.
The order code needs care in one place. In the SLVS232J addendum the DR line prints a 75 piece tube while the DR rows of the neighbouring voltages print 2500 on a large reel, and the package, quantity and marking columns sit one line off from the code column. The DR body is a large reel part, so a purchase order that reads the printed line rather than matching the code will ask for a tube that does not exist. SUPERB reconciles the code against the row before quoting, and the pin to pin cross reference page lists the flag and reset variants in the same body so a board can be reworked without a new footprint.
Questions buyers ask before ordering
Can the flag replace a reset input? Not directly. A reset input needs the signal to stay asserted through a brown out and for a fixed delay afterwards; a flag releases as soon as the rail is good and follows the rail back down without a delay.
Is the flag push pull? Open drain. It needs a pull up to the logic rail, and it can share that pull up with other open drain flags on the same net.
Does it need a minimum load for the flag to release? No. The comparator watches the output voltage, and the part regulates down to no load.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line and confirms the reel quantity from the code rather than from the printed line, because the addendum text is the one place where this family trips an order. A single line call is enough when the quantity sits below a full reel, and the answer names the tube or the reel explicitly. Send the rail, the load and the sequencing requirement through the one stop BOM sourcing page and the answer comes back with the code, the reel and the date code.