Contact Us

TPS62060DSGR

Brand: Texas Instruments
Texas Instruments TPS62060DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62060DSGR — Power Management & Signal Chain | Superb Automation

TPS62060DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62060DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62060DSGR: 1.6 A step-down converter at a fixed 3 MHz in a 2 mm by 2 mm package

TPS62060DSGR is a small synchronous buck converter that switches at a fixed 3 MHz so the inductor and the output capacitor fit in the space of a few millimetres in a WSON body of 8 pins. The TPS62060 runs from 2.7 V to 6 V and delivers up to 1.6 A at a fixed 3 MHz switching frequency, with the oscillator specified between 2.6 MHz and 3.4 MHz. It moves into power save mode at light load and back into fixed frequency pulse width modulation as the load rises, so a standby rail keeps its efficiency without a mode pin. Quiescent current is 18 uA typical and shutdown current is 0.1 uA. The reference is 600 mV and the feedback accuracy in pulse width modulation is plus or minus 1.5 percent.

Order code and package

Order codeTPS62060DSGR
Input voltage2.7 V to 6 V
Output current1.6 A
Switching frequency3 MHz fixed, 2.6 MHz to 3.4 MHz over temperature
Controlfixed frequency pulse width modulation with power save at light load
Voltage reference600 mV
Feedback accuracyplus or minus 1.5 percent in pulse width modulation
Quiescent current18 uA typical, 25 uA maximum
Shutdown current0.1 uA typical, 1 uA maximum
Package8 pin WSON, 2 mm by 2 mm
Internal discharge75 Ohm typical when disabled
DocumentSLVSA95B, March 2010, revised July 2015

Electrical parameters that decide the application

Switch current limit1.8 A minimum, 2.25 A typical, 2.7 A maximum
High-side resistance120 mOhm at 3.6 V in, 95 mOhm at 5 V in
Low-side resistance90 mOhm at 3.6 V in, 75 mOhm at 5 V in
Input UVLO falling1.73 V minimum, 1.78 V typical, 1.83 V maximum
Input UVLO rising1.9 V minimum, 1.95 V typical, 1.99 V maximum
Thermal shutdown150 C rising, 10 C hysteresis
Start-up time500 us from enable to 95 percent of the output
Load regulation-0.5 percent per A
Line regulation0 percent per V, typical
Discharge resistor75 Ohm typical, 200 Ohm maximum at 3.6 V
Duty cycleup to 100 percent in dropout
Enable thresholdshigh above 1 V, low below 0.4 V, over the 2.7 V to 6 V input range

Points to check before this part goes on a BOM

Three megahertz is the whole point of this part. At that frequency a 1 uH inductor and a 10 uF ceramic output capacitor hold the ripple within the load requirement, which is how the whole converter fits in a footprint a few millimetres on a side. The cost is switching loss, so the part is efficient at light and medium load and falls away at 1.6 A.

Power save mode is automatic and has a side effect on the output ripple. In pulse frequency mode the part skips cycles and the output sits slightly above nominal, because the internal reference is offset to about 1.01 times the value in that mode. A load that is sensitive to a 1 percent offset at light load should either keep the rail loaded or accept the positioning.

The current limit minimum of 1.8 A against a 1.6 A rating leaves a small margin, and the limit is the peak switch current rather than the average output current. With a 1 uH inductor at 3 MHz and a 3.6 V input the ripple is around 0.4 A, so the peak at full load is near 1.8 A, right at the minimum limit. A board that expects the full 1.6 A across the whole input range should check the ripple at the highest input voltage, where it is largest.

Start-up is quick and disciplined. The internal soft start brings the output to 95 percent in about 500 us, and during the first third of that ramp the switch current limit is cut to one third of nominal, which keeps a board with a large output capacitor from pulling the input rail down. On a 5 V rail feeding several of these converters the staggered start is what keeps the input from collapsing.

The discharge resistor is worth knowing about when a rail feeds a device that must not see a slow decay. When the enable pin goes low the part holds a resistor of 75 Ohm typical across the output, so a 1.2 V rail falls quickly instead of floating down through the load. On a rail that back powers from another supply this behaviour is a help, and on a rail that is deliberately held up it is a problem.

The 2 mm by 2 mm WSON has no room for a thermal via field, so the pad is the only path. At 1.6 A from 3.6 V to 1.2 V the loss is around 0.25 W, which at 1300 mW of rated dissipation is comfortable, but the same part at 5 V in and 1.2 V out runs closer to the limit. The document gives 75 C per W typical for the package on a four layer board.

Ordering the DSG suffix gives the 2 mm by 2 mm WSON. The fixed 3 MHz frequency means the part cannot be synchronised to a system clock, so a board that needs all its converters on one frequency for emission reasons should place this part away from sensitive traces rather than try to lock it.

Where this order code fits

This order code suits point of load rails in handheld instruments, portable medical monitors, wireless sensor nodes and camera modules where the board area under the converter is a few square millimetres and the load is a processor or a radio that sleeps most of the time. The 6 V input ceiling covers a single cell lithium battery and a 5 V system rail with margin. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the 3 MHz switching be synchronised externally? No. The oscillator is fixed, which is why the part is chosen for size rather than for a coordinated clock plan.

What happens in dropout? The part runs at 100 percent duty cycle, so the output follows the input less the resistive drop across the high-side switch.

Is the 1.6 A rating available over the whole input range? The rating is the same, but the ripple current grows with input voltage and the peak has to stay under the 1.8 A minimum current limit.

SUPERB supplies this order code with packing and date codes stated, and the Medical Device Components page covers the checks that matter when a small rail has to be filled from an alternate line.