Contact Us

THS6043ID

Brand: Texas Instruments
Texas Instruments THS6043ID is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS6043ID — Power Management & Signal Chain | Superb Automation

THS6043ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS6043ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS6043ID: dual ADSL line driver with a shutdown pin, in an 8 pin SOIC body

THS6043ID is the same 12 V line driver as the THS6042 with a TTL level shutdown input, so a line card can drop an unused port to 0.3 mA standby in a SOIC body of 8 pins. The shutdown block in the data sheet is written for the THS6043 only: standby current is 0.3 mA typical and 0.7 mA maximum, disable takes 0.5 microseconds, enable takes 0.2 microseconds, and the input draws 40 to 100 microamps depending on state. The thresholds are 0.8 V for power up and 2 V for power down, so 3.3 V logic drives it directly with 0.5 V of margin on the low side and 1.3 V on the high side.

Order code and package

Order codeTHS6043ID
Functiondual differential line driver with shutdown
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 6 V to plus or minus 15 V, 10 to 30 V single supply
Standby current0.3 mA typical, 0.7 mA maximum
Disable time0.5 microseconds
Enable time0.2 microseconds
Shutdown thresholds0.8 V for power up, 2 V for power down
Shutdown input current40 to 100 microamps
Bandwidth95 MHz at a gain of 2 into 25 ohms
Output current400 mA short circuit
Junction rangeminus 40 to plus 85 C, I suffix

Electrical parameters that decide the application

Offset voltage9.5 mV typical, 16 mV maximum
Differential offset1 mV typical, 5 mV maximum
Bias current3.5 microamps typical, 10 microamps maximum
Voltage noise2.2 nanovolts per root hertz at 10 kHz
Third order distortionminus 75 dBc at 16 V peak to peak, 250 kHz
Slew rate1000 volts per microsecond at 15 V rails
Quiescent current7.4 mA typical, 9.5 mA maximum per driver
Standby reductionfrom roughly 15 mA to 0.3 mA per package
Input common modeplus or minus 9.6 to plus or minus 10.1 V at 12 V rails
Output swing into 100 ohmsplus or minus 10.3 to plus or minus 10.8 V
Logic family3.3 V and 5 V compatible thresholds
DatasheetSLOS229, shutdown section applies to the 6043 only

Points to check before this part goes on a BOM

Standby current of 0.3 mA typical is not zero, and the maximum column is more than twice the typical. A card that budgets 0.3 mA per port for sixteen ports and then measures a hot board will find 0.7 mA per port, which is 11 mA of leakage that the supply calculation has to carry.

The shutdown thresholds are asymmetric and that is a feature on 3.3 V logic. Power down needs 2 V minimum, which 3.3 V logic supplies with 1.3 V of margin, and power up needs 0.8 V maximum, which a 0.4 V logic low satisfies. On a 1.8 V logic rail the high level is 0.2 V short of the guaranteed power down threshold, and a level translator becomes mandatory.

Enable is faster than disable by a factor of two and a half: 0.2 microseconds against 0.5 microseconds. In a system that uses the pin to blank a driver between transmit bursts, the turn on transient arrives before the amplifier has fully settled its bias, and the first few microseconds of a burst can carry a larger offset than the steady state table promises.

The shutdown pin draws 40 to 100 microamps, which is small but not negligible when it is driven by a microcontroller port through a series resistor. With a 10 kilohm series resistor the 100 microamp current drops a volt, which can push the pin below the 2 V power down threshold and leave the driver half on.

Everything else in the electrical table is the 6042 table. Offset of 16 mV maximum, 2.2 nanovolts per root hertz, minus 75 dBc at 16 V peak to peak and 1000 V per microsecond all carry over unchanged, so a board moving from the 6042 to the 6043 needs only the pin function checked, not the analogue performance.

Power up state is the on state, because 0.8 V or below enables the driver. A line card that wants the drivers muted until the FPGA has configured has to hold the pin high through a pull-up, and a floating pin driven only by a microcontroller that has not booted yet will come up transmitting.

Where this order code fits

Multi port ADSL cards use this part where a port has to be powered down when the subscriber is idle, and where the card controller needs to sequence the drivers after the line transformer has settled. The fast enable time also makes it usable as a pulse gate in instrumentation that has to blank a driver between acquisitions. Boards comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Is the THS6043ID a drop in replacement for the THS6042ID? Physically yes, same 8 pin SOIC, and the amplifier is identical. The difference is that pin 8 on the 6043 is the shutdown input, so the board has to drive it; leaving it floating is not a defined state.

How much power does the shutdown pin actually save? Package current falls from about 15 mA to 0.3 mA typical at 12 V rails, which is 180 mW down to 3.6 mW per package, and the maximum column is 0.7 mA, so budget 8 mW rather than 3.6 mW.

Can the shutdown pin be driven from 1.8 V logic? Not reliably. Power down needs 2 V minimum and 1.8 V logic guarantees 1.44 V at best, so the driver may stay enabled. Use a level translator or a small NMOS pull-down with a 3.3 V pull-up.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.