Contact Us

THS7001CPWP

Brand: Texas Instruments
Texas Instruments THS7001CPWP is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS7001CPWP — Power Management & Signal Chain | Superb Automation

THS7001CPWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS7001CPWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS7001CPWP: preamp plus 3 bit programmable gain amplifier in a 20 pin PowerPAD HTSSOP

THS7001CPWP is a two stage signal block on one die: a fixed gain preamp followed by a digitally controlled amplifier that steps from minus 22 dB to plus 20 dB in 6 dB increments in a HTSSOP body of 20 pins. The C suffix is the 0 to 70 C grade and the PWP suffix is the PowerPAD HTSSOP. Inside the package there are two separate blocks with separate supply pins: the preamp has 85 MHz of 0.1 dB flatness bandwidth at plus or minus 15 V and the programmable stage adds a 3 bit gain control with six decibel steps, giving minus 22 dB to plus 20 dB, which is 0.079 to 10 V per V.

Order code and package

Order codeTHS7001CPWP
Functionpreamp plus 3 bit programmable gain amplifier
PackageHTSSOP, 20 pins, PowerPAD, body code PWP
Supply rangeplus or minus 4.5 V to plus or minus 16.5 V
Gain rangeminus 22 dB to plus 20 dB in 6 dB steps
Bandwidth85 MHz at 0.1 dB flatness on 15 V rails, 35 MHz on 5 V rails
Slew rate65 volts per microsecond at 5 V, 85 at 15 V
Settling85 to 90 nanoseconds to 0.01 percent
Output current120 mA short circuit
Quiescent current5.5 to 7 mA preamp, 0.8 to 1.2 mA gain stage
Shutdown100 nanosecond disable, 1.5 microsecond enable
Junction range0 to 70 C, C suffix

Electrical parameters that decide the application

Offset voltage1 mV typical, 5 mV maximum
Offset drift10 microvolts per degree
Input offset current30 to 175 nanoamps, 0.3 nanoamps per degree
Voltage noise1.7 nanovolts per root hertz at 10 kHz
Current noise0.9 picoamps per root hertz at 10 kHz
Common-mode rejection80 dB minimum, 89 dB typical
Input common modeplus or minus 3.8 to plus or minus 4.2 V on 5 V rails
Output swingplus or minus 3.5 V into 150 ohms on 5 V rails
Distortionminus 88 dBc at 1 MHz with 2 V peak to peak into 250 ohms
Open-loop gain85 dB minimum, 89 dB typical
Full power bandwidth4.1 MHz at 5 V peak to peak on 5 V rails
Gain step accuracysix decibel steps, eight settings

Points to check before this part goes on a BOM

The gain range is digital, not analogue, and that decides how the block is used. Eight settings from minus 22 dB to plus 20 dB in 6 dB steps mean the gain error is quantised at 6 dB unless a second stage interpolates, so this part suits range switching and not fine level control. A system that needs 0.5 dB resolution needs a second control element.

Bandwidth and supply voltage are coupled through the feedback network. The 85 MHz figure is a 0.1 dB flatness number at a gain of 2 on plus or minus 15 V rails, while the same block on plus or minus 5 V rails gives 35 MHz. Two boards with the same part number and different rails do not have the same bandwidth, and the difference is a factor of 2.4.

The output stage is the limiting element on 5 V rails. Swing is plus or minus 3.5 V into 150 ohms, which is 7 V peak to peak, and full power bandwidth falls to 4.1 MHz at that amplitude because the slew rate is 65 V per microsecond. A 10 MHz signal at 5 V peak to peak is simply outside the part on 5 V rails.

Offset of 5 mV maximum is large next to the 1.7 nanovolts per root hertz noise. Over a 1 MHz bandwidth the noise is 1.7 microvolts, so the offset is three thousand times the noise and dominates any dc measurement. The part is a signal chain element for ac, and a dc coupled board has to trim or calibrate.

Current noise of 0.9 picoamps per root hertz through a 10 kilohm source is 90 nanovolts per root hertz, which is fifty times the voltage noise of the amplifier. Above a few kilohms of source impedance the current noise, not the amplifier, sets the noise floor, so a 50 ohm or 200 ohm source is where the 1.7 nanovolt figure is real.

The shutdown pin turns off both blocks, and the enable time of 1.5 microseconds is fifteen times the disable time of 100 nanoseconds. In a pulsed system that gates the receiver between transmit events, the asymmetry sets the minimum receive window: 1.5 microseconds of settling plus the 90 nanosecond settling of the amplifier itself before data is valid.

Where this order code fits

This part is used where a receiver needs a calibrated gain step under digital control: ultrasound front ends, automotive radar intermediate frequency chains, and automatic test equipment that has to switch ranges without a relay. The preamp also serves as a fixed gain block when the programmable stage is left at unity. Boards comparing it with a neighbouring part start from our How to Choose an RF Amplifier page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Can the programmable stage be bypassed? It can be set to a gain of 1, which is one of the eight settings, but it cannot be switched out of the signal path because both blocks share the die and the output. The preamp gain is fixed by external resistors.

Is this part a variable gain amplifier in the analogue sense? No. It is a stepped amplifier with eight discrete settings, so it changes gain in 6 dB jumps. The THS7530 in the same family is the continuous analogue control part.

What sets the gain step accuracy? The internal resistor network of the programmable stage. The data sheet gives the steps as nominal six decibel values, and any system that relies on the absolute gain has to calibrate each of the eight settings.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the RF Component Sourcing page sets out the checks that keep a substitute from failing on the bench.