Contact Us

TL061IDR

Brand: Texas Instruments
Texas Instruments TL061IDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL061IDR — Power Management & Signal Chain | Superb Automation

TL061IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL061IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL061IDR: single low power JFET input operational amplifier in an 8 pin SOIC body

TL061IDR is a single JFET input amplifier that runs on 250 microamps of supply current per amplifier and still gives 1 MHz of gain bandwidth in a SOIC body of 8 pins. The whole point of this order code is the supply current: 200 microamps typical and 250 microamps maximum per amplifier, with a total device dissipation of 6 to 7.5 milliwatts at 25 C. In exchange the offset window is 15 mV maximum at room temperature and 20 mV over the full range, the gain bandwidth is 1 MHz, and the slew rate is 3.5 V per microsecond, which is what a 1 MHz part can support.

Order code and package

Order codeTL061IDR
Functionsingle JFET input operational amplifier
PackageSOIC, 8 pins, body code D
Supply current200 microamps typical, 250 microamps maximum per amplifier
Dissipation6 to 7.5 milliwatts at 25 C
Gain bandwidth1 MHz
Slew rate3.5 volts per microsecond
Input resistance10 to the 12 ohms
Common-mode rangeplus or minus 11 V typical on 15 V rails, to 12 V below the positive rail
Temperature rangeminus 40 to plus 85 C, I suffix
Offset drift10 microvolts per degree
DatasheetSLOS081, low power JFET input family

Electrical parameters that decide the application

Offset voltage3 mV typical, 15 mV maximum at 25 C, 20 mV over full range
Input bias current30 picoamps typical, 200 picoamps maximum at 25 C
Input offset current5 picoamps typical, 100 picoamps maximum
Bias current over temperature7 nanoamps at the full range limit
Voltage noise30 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum, 86 dB typical
Supply rejection70 dB minimum, 95 dB typical
Large signal gain3 to 6 V per mV into 10 kilohms
Output swingplus or minus 12 V typical on 15 V rails into 10 kilohms
Channel separation120 dB
Unity gain stabilitystable at a gain of 1 with no compensation
Package thermal8 pin SOIC lead frame

Points to check before this part goes on a BOM

Fifteen millivolts of maximum offset is the number that decides the application. On a 12 bit converter running from 5 V, one bit is 1.22 mV, so the amplifier alone spends twelve bits of budget before the converter's own error is counted. This part belongs on a 10 bit channel or on an ac coupled path where the offset never appears in the measurement.

The bias current is small at room temperature and not small over temperature. Thirty picoamps typical becomes 7 nanoamps at the full range limit, a factor of 230, and through a 10 megohm source that is 70 millivolts. A high impedance sensor front end has to be evaluated at the temperature extreme, not at 25 C.

Supply current of 250 microamps maximum is what the part is bought for, and the other specifications are the price. Gain bandwidth of 1 MHz with 3.5 V per microsecond means a 10 V peak to peak sine is limited to about 56 kHz by slew rate, well below what the 1 MHz figure suggests, so a 100 kHz signal at full amplitude is already distorted.

Noise of 30 nanovolts per root hertz is high next to a precision bipolar part, and it is the reason this amplifier suits high impedance sources. Into a 100 kilohm source the resistor's own thermal noise is 40 nanovolts per root hertz, so the amplifier contributes less than the source; into a 1 kilohm source the amplifier is the whole noise floor.

Input resistance of 10 to the 12 ohms is a specification at 25 C and it falls with temperature. Leakage on the board becomes the real limit: a fingerprint or a flux residue on a high impedance node can be a nanoamp, which swamps the 30 picoamps the part itself draws.

The JFET input has a common mode range that stops about 4 V below the positive rail on a 15 V supply. A follower that tracks a signal to the positive rail will clip before the output does, and because the input stage inverts beyond that point, the failure is a phase reversal rather than a gentle limit.

Where this order code fits

Battery instruments, portable medical monitors and battery backed sensor nodes use this part where the signal is slow and the supply budget is a few hundred microamps. Its 10 to the 12 ohm input resistance also suits high impedance sources such as pH probes and piezoelectric sensors, where a bipolar input would load the source. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference between the TL061 and the TL071? Supply current and bandwidth. The TL061 runs at 250 microamps per amplifier with 1 MHz of gain bandwidth, and the TL071 runs at about 1.4 milliamps with 3 MHz. The input stage is the same JFET structure and the offset grades follow the same A and B pattern.

Can this drive a 10 kilohm load to plus or minus 12 V? Yes, the output swing on 15 V rails into 10 kilohms is plus or minus 12 V typical. Into 2 kilohms the swing falls and the data sheet's higher load condition gives plus or minus 10 V minimum.

Does the offset matter if the signal is ac coupled? Not for the reading, but it does for headroom. A 20 mV offset on a 5 V single supply is small, and on a gain of 100 stage it becomes 2 V at the output, which is most of the available swing.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.