Contact Us

THS7530PWP

Brand: Texas Instruments
Texas Instruments THS7530PWP is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS7530PWP — Power Management & Signal Chain | Superb Automation

THS7530PWP

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS7530PWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS7530PWP: wideband differential variable gain amplifier with 300 MHz bandwidth and analogue gain control

THS7530PWP is a continuous gain block with 11.6 dB to 46.5 dB of range on a single 5 V supply, controlled by a differential voltage with a 38.8 dB per volt slope in a HTSSOP body of 20 pins. The supply ceiling is the first thing to check: 5.5 V absolute maximum, with 4.5 to 5.5 V recommended, so this is a 5 V part and nothing else. Inside that rail it delivers 300 MHz of small signal bandwidth at every gain, 1250 V per microsecond of slew, 11 nanoseconds of settling to 1 percent, and third order output intercept of 21 dBm at 70 MHz.

Order code and package

Order codeTHS7530PWP
Functiondifferential variable gain amplifier
PackageHTSSOP, 20 pins, PowerPAD, body code PWP
Supply range4.5 to 5.5 V, 5.5 V absolute maximum
Gain range11.6 dB to 46.5 dB, which is 3.8 to 211.3 V per V
Gain slope38.8 dB per volt of control voltage
Bandwidth300 MHz at all gains
Slew rate1250 volts per microsecond at minimum gain
Settling11 nanoseconds to 1 percent
Output currentplus or minus 16 mA over temperature
Thermal resistance3.2 C per watt junction to case, bottom
Junction rangeminus 40 to plus 85 C

Electrical parameters that decide the application

Output offsetplus or minus 100 mV typical, plus or minus 340 mV maximum, 480 mV over temperature
Output common-mode offset4.5 mV typical, 12 mV maximum
Differential input impedance8.5 kilohms in parallel with 3 pF
Input bias current20 to 39 microamps, offset below 150 pA
Voltage noise1.1 nanovolts per root hertz above 100 kHz
Noise figure9 dB with a 50 ohm source
Second harmonicminus 65 dBc at 32 MHz with 1 V peak to peak
Third harmonicminus 61 dBc at 32 MHz with 1 V peak to peak
Third order intercept21 dBm at 70 MHz
Intermodulationminus 62 dBc at minus 10 dBm per tone, 200 kHz spacing
Output swing3.275 to 3.5 V high, 1.5 to 1.7 V low on 5 V
Control input0 to 1 V differential, 2.5 V default with no connection

Points to check before this part goes on a BOM

Gain control slope of 38.8 dB per volt means the control node is part of the signal path. One millivolt of noise or ripple on the control voltage is 0.039 dB of gain modulation, which on a 35 dB range is small, but 10 mV of 50 Hz ripple is 0.39 dB, enough to put a visible envelope on a received pulse train.

The output offset is the largest error term in the part. Plus or minus 340 mV maximum at room temperature and 480 mV over temperature, on an output that swings between 1.5 V and 3.5 V, leaves very little of the 2 V window for signal. A dc coupled analog to digital converter behind this amplifier has to be ac coupled or the offset has to be removed in the digital domain.

The 5.5 V absolute maximum is unusually tight and it rules out the obvious shortcut. A board that reuses a 12 V rail through a linear regulator has to guarantee that the regulator cannot overshoot at startup or during a load dump; a 6 V transient is outside the part and the failure mode is destructive, not recoverable.

Noise figure of 9 dB with a 50 ohm source is set by the input stage, not by the 1.1 nanovolts per root hertz. For a 50 ohm source at room temperature the thermal noise floor is 0.9 nanovolts per root hertz, so 1.1 nanovolts would suggest about 1.8 dB, and the missing 7 dB is the input structure and the gain setting. A receiver budget built on the voltage noise number alone will be optimistic by a wide margin.

Output current of plus or minus 16 mA over temperature is small for a 50 ohm load. Driving 2 V peak to peak into 50 ohms differential needs 20 mA peak, which is above the guaranteed figure, so this part expects a high impedance load such as an ADC input or a buffer, not a cable.

The gain range starts at 11.6 dB, not at unity or below. Minimum gain is 3.8 V per V, so the part cannot attenuate, and a system that needs less than 11.6 dB of gain has to add a fixed attenuator ahead of it. That attenuator then sets the noise figure for the whole chain.

Where this order code fits

Radar and electronic warfare receivers, ultrasound time gain compensation, and any automatic gain control loop that has to hold a constant output level across 35 dB of input variation. The differential input and output also make it a natural fit for driving a differential analog to digital converter directly. Boards comparing it with a neighbouring part start from our How to Choose an RF Amplifier page, and boards replacing a part that has gone end of life start from the LNA Selection Guide page.

Questions buyers ask

Is the gain control linear in volts or in decibels? In decibels. The slope is 38.8 dB per volt, so the gain in decibels is a straight line against the control voltage, which makes the loop mathematics of an automatic gain control simple but makes the control node sensitive to noise.

What supply does this part need? A single 5 V rail, 4.5 to 5.5 V. The absolute maximum is 5.5 V, so any 12 V or 15 V rail has to be regulated down with margin for overshoot.

Can it drive a 50 ohm cable? Not at full swing. The guaranteed output current is plus or minus 16 mA, and 2 V peak to peak into 50 ohms needs 20 mA, so a cable driver or a buffer stage belongs after this part.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the RF Component Sourcing page sets out the checks that keep a substitute from failing on the bench.