Contact Us

TPS51117RGYR

Brand: Texas Instruments
Texas Instruments TPS51117RGYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51117RGYR — Power Management & Signal Chain | Superb Automation

TPS51117RGYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51117RGYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51117RGYR: a single phase synchronous buck controller that runs from a separate 5 V housekeeping rail, holds 750 mV of reference to within 1 per cent and switches anywhere from 100 kHz to 550 kHz

TPS51117RGYR is a controller with an emulated on-time loop that needs no compensation network, a low side on resistance current sense that loses no efficiency, and an integrated boost diode so the high side gate drive does not need an external capacitor and diode in a VQFN body of 14 pins. The RGY body is fourteen pins on a 3.50 mm by 3.50 mm pad, and the part exists for point of load rails in a notebook or a set top box where the 5 V housekeeping rail is already there.

Order code and package

Catalogue stringTPS51117RGYR, where RGY is the fourteen pin VQFN and R is the large tape and reel
BodyVQFN, RGY, fourteen pins, 3.50 mm by 3.50 mm, and the same die in a fourteen pin TSSOP as the PW body
Reel3000 pieces on a large tape and reel on the RGY row, against 2000 on the TSSOP row
Finish and moistureNIPDAU plating, level 1 at 260 C on the plain row and level 2 on the .A row of the same body, which is a split in the addendum worth reading before a line is qualified
Temperatureminus 40 to 85 C only, so a board that has to run at 105 C ambient needs a different controller
Marking51117 on both bodies
DocumentSLVS631C, December 2005, revised May 2015
StatusActive and in production on the addendum dated November 2025

Electrical parameters that decide the application

Conversion input1.8 V to 28 V on the drain of the high side FET, independent of the controller supply, so a 20 V adapter rail and a 1.8 V point of load rail can share one part number
Controller supply4.5 V to 5.5 V on the V5FILT pin from another regulator, and the part does not generate its own housekeeping rail
Output0.75 V to 5.5 V adjustable, set by a divider against the 750 mV reference
Reference accuracyplus or minus 0.9 per cent at 25 C, 1.3 per cent from 0 to 85 C and 1.6 per cent over the full range, with 0.02 uA of input current so a high value divider is allowed
Switching frequency100 kHz to 550 kHz set by a 100 kOhm to 600 kOhm resistor on the TON pin, with 750 ns of on time at 12 V in and 2.5 V out on a 250 kOhm resistor
Current senselossless low side on resistance sensing with a 30 mV to 200 mV trip window and 4500 ppm per degree of temperature compensation
Negative current limita separate comparator with a 10.5 mV offset, so a converter that is back driven trips instead of boosting the input
Soft startinternal, 0.82 to 1.5 ms from the enable crossing to regulation, with no external capacitor
Protectionovervoltage at 111 to 119 per cent of the reference with a 1.5 us response, undervoltage at 65 to 75 per cent with hysteresis, and a thermal shutdown
Output discharge20 to 32 Ohm across the output when the enable is low, so a rail is drained rather than floating on a restart
Supply current400 to 750 uA in forced PWM, 250 to 470 uA in auto skip and 4.5 to 7.5 uA in shutdown
Power goodan open drain output referenced to the 750 mV sense point, with a fixed delay

Where this part sits against the alternatives

TPS51117RGYRfourteen pin VQFN, 3000 pieces, level 1 moisture on the plain row and level 2 on the .A row, this page
TPS51117PWRthe same die in a fourteen pin TSSOP, 2000 pieces on a large reel, for a board that has no room for a QFN reflow window
TPS51117PW90 pieces in a tube, which is the row a prototype order usually lands on
Sibling controllers in the same familythe part is the single phase member of a line that shares the on-time pin and the 750 mV reference, so a two phase rail moves up within the family rather than to another vendor
Competing approach with an integrated FETa converter with the FETs on the die removes the gate drive and the sense resistor but caps the current at a few amps and fixes the frequency
Competing approach with a fixed frequency controllera voltage or current mode part needs a compensation network and a sense resistor, and brings a loop that has to be measured on every board revision

Points to check before this part goes on a BOM

The separate 5 V supply is the constraint that decides whether this part fits. The controller does not run from the rail it converts, so a board that only has 12 V and needs 1.2 V must generate 5 V first. In a notebook that 5 V is already there and the constraint costs nothing, and in an isolated converter it costs an extra winding. Reading the block diagram before the circuit diagram is the difference between a one page bill of materials and a second board spin.

The on-time loop is why there is no compensation network. The on time is computed from the input and output voltages with a resistor setting the period, so the loop behaves like a fixed frequency converter without an error amplifier to compensate. That is the whole appeal for a point of load rail that has to be stable into ceramic output capacitors with almost no ESR. The price is that the switching frequency moves with the load and the input, and the data sheet shows the curves rather than promising a fixed number.

Lossless current sense has one trap. The trip point is set by the voltage across the low side FET while it conducts, so the current limit moves with the on resistance of that FET, which moves with temperature, and the part compensates at 4500 ppm per degree to hold the trip point roughly constant. The compensation assumes a particular FET, and a substitution to a part with a much lower on resistance lowers the effective current limit unless the trip resistor is changed with it. That is the sort of second source that passes a bench test and fails on a cold morning.

The temperature rating is the other hard stop. The whole device is specified to 85 C, which is a commercial range, and the junction will be well above ambient in a QFN with no thermal pad connection to a plane. A 1.05 V rail at 15 A with 90 per cent efficiency dissipates 1.7 W in the FETs and not in the controller, so the controller stays cool, but a 60 C ambient with any local heating leaves little margin. Industrial boards with a 105 C ambient requirement should look at the automotive members of the family.

The addendum prints level 1 moisture on the plain RGYR row and level 2 on the RGYR.A row of the same body. Both are the same part electrically and the difference is a packing qualification, so a line that runs a 260 C reflow for 30 seconds can use either, and a line that stores opened reels for months should prefer the level 1 row. It is a small point that becomes a real one when a reel has been open on a shelf for a year and the floor life clock matters.

The V5FILT pin has an absolute maximum that is easy to exceed during a hot plug. The pin is a 5.5 V input with no divider, and a 12 V rail that rings on insertion can exceed it before the housekeeping rail is up. A series resistor and a 1 uF capacitor at the pin, plus a check of the sequencing, keep the controller alive through a hot plug event that the FETs survive.

Choosing the on-time resistor

The on time follows 19e-12 times the resistor times two thirds of the output voltage plus 100 mV, plus 50 ns. With a 250 kOhm resistor and a 2.5 V output that is about 750 ns, which at a 12 V input is a duty cycle of 21 per cent and a period of 3.6 us at the switching frequency the curve shows. Doubling the resistor halves the frequency and doubles the ripple current, so the inductor and the output capacitor have to move with it.

The minimum off time is the limit on the other end. A 28 V input and a 0.75 V output is a duty cycle of 2.7 per cent, and the controller cannot go below its minimum off time, so the frequency falls as the input rises. That is normal for an on-time loop and it means the ripple at 28 V is larger than the ripple at 12 V. A board that must hold a tight ripple across the whole input range needs to check the curve at the top of the range, not the middle.

Setting the current limit from the FET, not from the load

The trip voltage is set by a resistor to a 30 to 200 mV window and the resulting current is that voltage divided by the low side on resistance. A 4 mOhm FET with a 60 mV setting trips at 15 A, which is the right number for a 12 A rail. Change the FET to a 2 mOhm part and the same 60 mV trips at 30 A, which no longer protects the inductor. The resistor has to move with the FET, and the temperature compensation assumes the two are matched.

The negative limit comparator is set by the same pin and trips when the inductor current flows backwards beyond the offset. In a converter that feeds a rail which can be back driven, that protects the input from being pumped up. In a converter that sinks current by intent, the same comparator limits how much it can sink, and the offset of 10.5 mV is the number that decides the limit.

Where this order code fits

This is the point of load controller for the core and input output rails in a notebook, a set top box, an industrial gateway or a network appliance, where the 5 V housekeeping rail is already available and the rail that has to be regulated sits between 0.75 V and 5.5 V at anything from a few amps to twenty Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it run from the 12 V rail it converts? No. The controller needs 4.5 V to 5.5 V on V5FILT from another source, and the conversion input on the FET drain can then be anywhere from 1.8 V to 28 V.

Does it need loop compensation? No. The emulated on-time loop is set by the TON resistor and is stable into ceramic output capacitors without a compensation network.

What sets the current limit? The voltage across the low side FET while it conducts, with a 30 to 200 mV window and 4500 ppm per degree of compensation. Change the FET and the limit changes with it.

Is 85 C enough for an industrial board? The whole device is specified to 85 C, so a 105 C ambient requirement needs a part from the automotive members of the family, not this one.

What happens when the enable goes low? The output is discharged through a 20 to 32 Ohm path, so the rail falls instead of floating, and the controller itself draws 4.5 to 7.5 uA.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.