TPS3110E15DBVR
Product Specifications
TPS3110E15DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3110E15DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3110E15DBVR: 1.5 V voltage supervisor with watchdog, 1.2 microamp, 130 ms reset delay, SOT-23-6
TPS3110E15DBVR is a supply supervisor that holds a processor in reset while its rail is out of range and watches for a missing clock edge after the rail is good in a SOT-23-6 body of 6 pins. The sense threshold on this string is the 1.5 V option, with a trip point accuracy of 0.75 per cent and a supply current of 1.2 microamp typical. Reset is asserted from a supply as low as 0.4 V, which means the output is defined before the rail is usable, and the release is delayed by 130 ms after the threshold is crossed. The watchdog input expects an edge inside its timeout window and pulls reset low again if the processor stops talking.
Order code and package
| TPS3110E15DBVR | Active, SOT-23 (DBV) body, 6 pins, 250 pieces on a small reel, marking PGKI |
| TPS3110E15DBVT | Active, the same silicon with 3000 pieces on a large reel and a different marking |
| TPS3110E09DBVR | the 0.9 V sense option, same body, for a lower core rail |
| TPS3103 and TPS3106 | the same supervisor without the watchdog, in the same body |
| Temperature range | minus 40 to 125 degrees |
Electrical parameters that decide the application
| Sense threshold | 1.5 V nominal on this string, with a 1.434 V trip point printed in the selection table |
| Threshold accuracy | 0.75 per cent over temperature |
| Supply current | 1.2 microamp typical |
| Reset output | push pull or open drain depending on the family member, active low |
| Reset delay | 130 ms from the threshold crossing to the release |
| Minimum supply for a defined output | 0.4 V |
| Watchdog | present on the 3110 member, absent on the 3103 and 3106 members |
| Reel sizes | 250 pieces on the R string, 3000 on the T string |
Family variants and how they differ
| TPS3110 | supervisor with a watchdog input, the string on this page |
| TPS3103 | supervisor with an open drain reset and no watchdog |
| TPS3106 | supervisor with a push pull reset and no watchdog |
| Threshold options | 0.9 V, 1.2 V, 1.5 V, 1.6 V, 2 V and 3.3 V, chosen in the order code |
| Reset polarity | active low on every member of the family |
Points to check before this part goes on a BOM
A supervisor is specified by its threshold, not by its supply range. The 1.5 V option trips at about 1.434 V, which is below a 1.5 V rail by 4.4 per cent. That window is the whole point: the processor must be held in reset while the rail is below the minimum it can run at, and released only when the rail is above it. A rail with a 5 per cent tolerance and a 1.5 V minimum sits uncomfortably close to that trip point, and the two tolerances have to be compared rather than assumed.
One point two microamp is what makes it usable on a battery rail. A supervisor sits on the rail it watches, so its own current is a permanent load. At 1.2 microamp it is negligible against a sleeping microcontroller, and it is far below the self-discharge of most cells. A part with 50 microamp of supply current would dominate the sleep budget of a small product.
Reset is defined from 0.4 V, which prevents a false start. Many supervisors leave their output undefined until the supply reaches a volt or more, and a processor with a low threshold can start executing out of an undefined reset state. This family drives reset low from 0.4 V, so the processor is held from the moment the rail begins to rise. That is the reason the part appears in products that have field returns from sporadic start failures.
The watchdog is a separate function from the supply monitor. It expects an edge on its input inside a timeout window and pulls reset low if the processor stops servicing it. A firmware loop that hangs produces a reset instead of a frozen product. A board that does not use the watchdog still has to drive the pin, because a floating input on some members is read as a timeout and resets the processor repeatedly.
A 130 ms delay is chosen against the requirement of the processor. The release has to come after the clock is stable and after the supply has finished its ramp, and before the boot timeout of the processor expires. A board that needs a longer delay cannot stretch this one, because it is fixed internally, and the family member with an external capacitor is the answer.
Packing is 250 pieces on the R string and 3000 on the T string. That is unusual for a six pin part and it catches purchase orders. A production run of 1000 pieces needs four small reels on the R string, and the line time for those reel changes is real. The T string exists for exactly this reason and carries the same silicon.
The supply pin needs a decoupling capacitor even at 1.2 microamp. The part draws almost nothing in steady state, but it has to respond to a fast rail dip, and without local capacitance the response is set by the trace inductance to the bulk capacitor. A 100 nanofarad part next to the pin is the usual answer and it is not optional on a board with a switching supply nearby.
The trip point is specified at 0.75 per cent and that is tight for a supervisor. It means the threshold at which reset is released moves by about 11 mV across the full temperature range on this option, which is small enough that the rail tolerance, not the supervisor, decides the margin. A part with a 2 or 3 per cent threshold window would leave the processor starting on a rail that is below its own minimum, and that shows up as a product that fails to boot in a cold room.
Watchdog and reset outputs are open drain on some members and push pull on others. An open drain output needs a pull up and can be wired with other reset sources. A push pull output cannot be wired in parallel without a series element. The two are the same function with different interfaces, and a substitution across them changes the board, not just the part.
What to confirm before this part goes on a purchase order
State the rail being watched and its tolerance. The threshold option is part of the order code, and a supervisor with the wrong threshold either resets a healthy processor or misses a bad rail.
Say whether the watchdog is used, and if it is not, how the pin is driven. An undriven watchdog input turns a useful supervisor into a source of repeated resets.
Where this order code fits
It holds a processor or a DSP in reset until its supply is valid and its clock is stable, and watches the supply for a dip afterwards. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What is the difference between this part and the TPS3103? The watchdog input. TPS3110 has it and the 3103 does not, and the reset output type also differs across the family, with open drain on some members and push pull on others. The supply monitoring function is the same.
Can it supervise a 1.8 V rail? Not with the 1.5 V option in a useful way. The threshold is fixed by the order code, so a 1.8 V rail needs the 1.6 V option, and the 1.5 V part would release the processor while the rail was still below its minimum. The threshold is chosen against the rail, not against the processor family.
How long is reset held after the rail is good? About 130 ms. The delay starts when the monitored rail crosses the threshold on the way up and it is fixed internally. A processor that needs longer has to add its own delay or use a member of the family with an external capacitor.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.