Contact Us

TPS2001EDBVR

Brand: Texas Instruments
Texas Instruments TPS2001EDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2001EDBVR — Power Management & Signal Chain | Superb Automation

TPS2001EDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2001EDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2001EDBVR 2 A current limited power distribution switch with output discharge in the 5 pin SOT-23 body

The TPS2001EDBVR is a 2 A power distribution switch in the SOT-23 five pin body, with a fixed current limit, output discharge, reverse current blocking and a built in soft start. It is the active high enable member of the TPS20xxE family, which covers 1.5 A and 2 A parts and is the newer generation of the TPS20xxC family. The part works from 2.7 to 5.5 V, which covers both the 3.3 V and the 5 V rail, and it is AEC free but automotive adjacent in the sense that the family is used widely in infotainment and cluster modules.

The E family differs from the C family in two ways that matter to a board. The output is discharged when the switch is off, which brings a rail down in a controlled way instead of leaving it floating with whatever charge the load holds. The current limit window is also different, with a 2 A member limiting between 2.24 A and 3.36 A at room temperature. Both changes are visible only in the electrical table, so a customer who substitutes one family for the other on a bill of materials gets a board that works on the bench and behaves differently at power down.

Key parameters taken from the TPS2001EDBVR document

Rated current2 A continuous for this member, with a 1.5 A member in the same family and body
Current limit2.24 A minimum, 2.8 A typical and 3.36 A maximum at 25 C, widening to 2.1 to 3.5 A over minus 40 to plus 125 C
Response time1.5 microseconds typical to a short circuit, measured with a 50 milliohm short
Output dischargeFitted, with a 400 to 810 ohm discharge resistance and 500 ohms typical when the switch is off
On and off time3 ms typical into a 100 microfarad load with a 10 ohm load resistance
EnableActive high enable on this member, with the active low equivalent in the same family and pinout
Reverse current blockingFitted, so the output does not feed back into a collapsed input
Supply2.7 to 5.5 V operating, with an absolute maximum of 6 V on the input, output and enable pins
Logic levels1.8 V high level minimum and 0.8 V low level maximum, so the part works from a 1.8 V controller
Quiescent current93 microamps typical and 118 microamps maximum with the switch enabled, 0.5 microamps typical disabled
ESDPlus or minus 2 kV human body model, plus or minus 500 V charged device model, and plus or minus 8 kV contact and 15 kV air gap on the output pin
CertificationUL listed and CB file E169910
BodySOT-23 5 pins, 2.9 by 1.6 mm, with VSSOP and HVSSOP options in the family
Order code factsTPS2001EDBVR, SOT-23 DBV 5 pins, 3000 pieces on a large reel, NIPDAU finish, moisture level 1 with unlimited floor life, minus 40 to plus 125 C

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The current limit window on the 2 A member is wide, from 2.24 A to 3.36 A at room temperature, and it widens further over temperature. A load that draws 2.3 A sits inside the rating and inside the limit, but only just, and at the cold end the limit may be at its upper bound. A product that has to guarantee a 2 A delivery into a load that can draw more should look at the thermal path and the supply, not only at the limit, because the part will hold the current and heat up rather than shut down.

The output discharge is the feature that changes system behaviour. A rail that feeds a module with a large capacitor holds its charge for seconds after the switch opens, and a controller that expects the rail to be down before the next power up sees a false ready signal. The 500 ohm discharge resistance brings a 100 microfarad load down with a time constant of 50 ms, which is fast enough for a retry sequence and slow enough not to dump a large current into the switch. The same function is absent on the C family members without discharge.

The 3 ms on time into a 100 microfarad load is the soft start, and it is what keeps the inrush inside the current limit. A larger load capacitor lengthens the rise and the part holds the current limit for longer, which is the intended behaviour but also the thermal event. A product with a very large capacitor on the output, for example a motor driver with bulk storage, needs the rise time and the dissipation checked together, because the part will sit in current limit for the whole ramp.

The 1.8 V logic threshold matters on modern boards. A controller running from 1.8 V cannot drive a switch that needs 2.5 V on its enable pin, and a level shifter adds a part and a failure mode. This family specifies a 1.8 V high level minimum, so it can be driven directly from the low voltage rail. The output pin also carries 8 kV of contact ESD and 15 kV of air gap discharge, which is what a user accessible connector needs, and that rating is on the output pin rather than on the whole part.

  • Current limit window against the maximum load current, including the cold end of the temperature range.
  • Power down behaviour of the rail with the real load capacitor, since the discharge resistor sets the fall time.
  • Inrush and rise time into the actual output capacitor, with the part held in current limit for the ramp.
  • Fault pin timing during a short, and the recovery path after the short is removed.
  • Quiescent current with the switch enabled at the top of the temperature range.
  • ESD performance on the connector side, since the output pin rating is what a user accessible port relies on.

Which projects this part fits

This part fits USB ports on notebooks, desktops and docking stations, televisions and connected peripherals, printers, data centre and enterprise computing boards, and any 5 V rail that has to be protected from a downstream fault with a fast response. It also fits industrial equipment with a user accessible connector and medical carts where a cable fault must not take the system down. Customers who need the rail to come down quickly at power off use this member, and customers who need the rail to hold use the member without discharge.

Questions that come up before a purchase order is released

What is the difference between the E and the C family?

The current limit window, the discharge behaviour and the body options. The E family adds output discharge on every member, uses a different limit window and is offered in SOT-23 and the two 8 pin bodies. The pinout of the five pin body is compatible, so a substitution is physically possible and electrically different, which is why the part number has to be checked rather than the footprint.

Why is the enable active high on this part?

Because the family offers both polarities and this member is the active high one. A board that drives the enable from a controller with a default low output wants the active low member, so that the rail is off until the controller is ready. The choice is made once, at the drawing stage, and it is the reason the two parts exist in the same body.

How much capacitance can it drive?

There is no hard limit in the document, but the inrush is limited by the current limit and the soft start, so a large capacitor means a longer time in current limit and more dissipation. A 100 microfarad load rises in about 3 ms. A 1000 microfarad load takes ten times as long and the part dissipates for that whole window, which on a SOT-23 body is the thermal limit rather than the electrical one.

Does the discharge resistor affect normal operation?

No. It is only connected when the switch is off, and its 500 ohm value draws a negligible current from the source while the rail is up. It does mean that a rail held up by a second source will be loaded by the discharge resistor when this switch is off, which matters in a system with two supplies feeding one node.

How is the part checked at incoming inspection?

Reel and marking check, and a functional test on a board that applies a load, shorts the output, reads the fault pin and confirms the rail comes down at power off. The discharge function is worth testing explicitly, because a substitution with the non discharge family member leaves the board working and only shows up as a power sequencing fault in the field.

How SUPERB handles this line

We supply the TPS2001EDBVR from original reels with lot and date code traceability, and we check that the part is the discharge member rather than a pin compatible substitute because the difference only appears at power down. The power management cross reference page lists the power switch families we carry with their limit windows, pin to pin cross reference covers the compatible bodies across the two generations, and BOM shortage recovery is the page to read when a build is short of one member and a substitute has to be checked properly.