Contact Us

TMS470R1A256PZ-T

Brand: Texas Instruments
Texas Instruments TMS470R1A256PZ-T is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS470R1A256PZ-T — Power Management & Signal Chain | Superb Automation

TMS470R1A256PZ-T

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS470R1A256PZ-T from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS470R1A256PZ-T: 256K byte ARM7TDMI flash microcontroller in a 100 pin body, T temperature grade to 105 C

TMS470R1A256PZ-T is the same 256K byte ARM7TDMI device as the plain PZ code, with the T grade in the suffix fixing the ambient range at minus 40 to 105 C in a LQFP body of 100 pins. The body and the silicon are the A256: 24 MHz system clock with a 48 MHz pipeline mode, 256K bytes of flash in fourteen contiguous sectors, 12K bytes of SRAM, a 16 channel high end timer, a ten bit 16 channel ADC and a CAN controller. The difference sits at the end of the order code, where the T grade replaces the standard industrial window with minus 40 to 105 C, twenty degrees more than the bottom grade and twenty less than the Q grade.

Order code and package

Order codeTMS470R1A256PZ-T
CoreARM7TDMI, 16 and 32 bit, big endian
Clock24 MHz, 48 MHz in pipeline mode
PackageLQFP, 100 pins, body code PZ
Flash256K bytes, 14 contiguous sectors
SRAM12K bytes, plus 1K byte HET RAM
High end timer16 channels, 14 high resolution
ADC10 bit, 16 inputs, 64 word FIFO
Serialtwo SPI, two SCI, one CAN controller
Core supply1.81 to 2.05 V
Temperatureminus 40 to 105 C, T grade
DatasheetSPNS100B, revised August 2006

Electrical parameters that decide the application

Temperature gradeT, minus 40 to 105 C, defined in the family nomenclature
Junction limitminus 40 to 150 C
Flash endurance50 000 cycles at the full temperature range
Sector erase1.7 s typical
ADC inputs16, 64 word FIFO, shared with digital functions
CANsingle controller, 16 mailboxes, 2.0B
HET RAM64 instructions, 1K byte
Watchdoganalog watchdog, external RC network
Clock modulezero pin PLL, multiply by 8
Low powerSTANDBY and HALT
I/O supply3.0 to 3.6 V
Package thermal100 pin LQFP, thermal resistance in the data sheet

Points to check before this part goes on a BOM

The T grade is a real twenty degree difference, and it is the reason this code exists next to the plain PZ. A board that runs at 95 C inside a cabinet is outside an 85 C part and inside this one, with the same footprint, the same firmware and the same peripheral set. Moving up to the Q grade to 125 C buys margin that costs money and is often not needed.

Flash retention and endurance are specified over the range, so a part that stores calibration in the last sector is still writing within specification at 105 C. What is not covered is a write cycle that starts at 105 C and ends after the cabinet has cooled; the erase and program times in the data sheet are for a stable temperature, and a long erase during a thermal transient is the classic way to lose a sector.

The junction limit of 150 C is not the ambient limit. At 105 C ambient in a sealed box the junction is higher by the thermal resistance of the 100 pin body times the dissipation, and the dissipation is dominated by the core plus the I/O ring. Check the number rather than assuming headroom, because twenty degrees disappears quickly.

The one CAN controller is the limit on this device. Two networks need the A288, and that part also brings the expansion bus and two more PWM channels. Boards that were specified with the A256 and later needed a second bus usually end up re-spinning rather than moving up, so the decision is worth making at the block diagram stage.

The ADC shares its sixteen inputs with digital functions, and at 105 C the leakage on an input driven from a high impedance source rises. A sensor divider above about 10 kohm into this converter will read low in a hot cabinet; buffering the input or lowering the divider impedance is the fix, and it costs less than a board revision.

The analog watchdog needs its external RC network to work. It is not an internal timeout; it resets the device when the software stops servicing it, provided the RC is fitted and the AWD pin is not left floating. Boards that tie the pin to ground on the bench and leave it that way in production lose the watchdog silently.

Where this order code fits

Automotive body and chassis modules, under hood sensor interfaces that stay below 105 C, industrial drives in unventilated cabinets, outdoor metering and telecom nodes, and any existing board that was qualified on the T grade and is now being re-sourced. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the -T suffix a different die? No. The silicon and the pinout are the A256; the suffix marks the T temperature grade, minus 40 to 105 C. The same body is also sold in the Q grade to 125 C, and the two are not the same order code.

Can this part drive two CAN networks? No, it has a single CAN controller with sixteen mailboxes. Two networks need the A288, which carries two SCC controllers and an expansion bus in the 144 pin body.

What has to change on a board moving from 85 C to this grade? The thermal path and the capacitors, and the ADC source impedance. The footprint, the firmware and the peripheral set do not change, which is what makes the temperature upgrade a re-order rather than a re-spin of the board.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.