Contact Us

OPA445AP

Brand: Texas Instruments
Texas Instruments OPA445AP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA445AP — Power Management & Signal Chain | Superb Automation

OPA445AP

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA445AP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA445AP: high-voltage operational amplifier rated to plus or minus 45 V in an 8-pin plastic DIP

OPA445AP is a high-voltage operational amplifier that runs from plus or minus 10 V to plus or minus 45 V with 15 volts per microsecond of slew and a JFET input in a PDIP body of 8 pins. The AP suffix is the 8-pin plastic DIP, the commercial and industrial grade in the standard pinout that also covers TO-99 and SO-8 bodies. Supply rails go to plus or minus 45 V, offset is 1.5 millivolts typical and 5 millivolts maximum, drift is 10 microvolts per degree, gain bandwidth is 2 MHz with 15 volts per microsecond, and the input bias current is 50 picoamps at 25 C rising to 20 nanoamps over the specified temperature range.

Order code and package

Order codeOPA445AP
Functionhigh-voltage operational amplifier, unity gain stable
PackagePDIP, 8 pins, body code P, standard high-voltage pinout
Supply rangeplus or minus 10 V to plus or minus 45 V
Supply current4.2 milliamps typical, 4.7 milliamps maximum
Gain bandwidth2 MHz
Slew rate15 volts per microsecond
Offset1.5 millivolts typical, 5 millivolts maximum on the AP grade
Offset drift10 microvolts per degree
Input bias current50 picoamps maximum at 25 C, 20 nanoamps over temperature
Input common mode5 V inside either rail at plus or minus 40 V
DatasheetOPA445 high-voltage family document

Electrical parameters that decide the application

Power-supply rejection4 microvolts per volt typical, 100 microvolts per volt maximum
Voltage noise15 nanovolts per root hertz at 1 kHz
Current noise6 femtoamps per root hertz at 1 kHz
Input offset current4 picoamps typical, 40 picoamps maximum, 10 nanoamps over temperature
Grade comparisonthe BM grade holds 1 millivolt typical and 3 millivolts maximum
BodiesTO-99, DIP-8 and SO-8 in the same pinout
Operating rangeminus 25 to plus 85 C for the specified limits

Points to check before this part goes on a BOM

Bias current at temperature is the specification to work around. At 25 C the input draws 50 picoamps, which through a 10 megohm feedback resistor is 0.5 microvolts and irrelevant. Over the specified range the same input draws up to 20 nanoamps, which through the same resistor is 200 microvolts, and through 100 megohms it is 2 millivolts, four times the room temperature offset. A JFET input doubles its leakage roughly every 10 degrees, and a high voltage stage often runs warm.

The common-mode range stops 5 V inside either rail at plus or minus 40 V, so the usable input window is 70 V of the 80 V supply. That is a real limit for a differential pair, and it is the reason a high voltage stage that wants to sense the rail directly needs either a divider or a different input topology. A signal at plus or minus 42 V with a plus or minus 45 V supply is outside the specified range.

15 volts per microsecond at 80 V peak to peak is a full power bandwidth of about 30 kHz, and the 2 MHz gain bandwidth allows 200 kHz at a gain of 10. A piezoelectric actuator driven at 10 kHz and 60 V peak to peak needs 3.8 volts per microsecond, so the part has margin for the fundamental and none for the third harmonic of a fast edge. A square wave drive at 10 kHz will arrive with visible rounding on the corners.

4.2 milliamps at plus or minus 45 V is 378 milliwatts of quiescent dissipation, and 4.7 milliamps is 423 milliwatts. The DIP body has to pass that continuously before it drives any load, and driving a capacitive load at high frequency adds to it. This is the reason the high voltage families are usually specified with a derating curve rather than a single ambient limit, and the quiescent figure alone puts the junction about 40 degrees above ambient in a plastic DIP.

The AP grade is 1.5 millivolts typical and 5 millivolts maximum against the BM grade at 1 millivolt typical and 3 millivolts maximum. The difference is a screening step and a temperature range, not silicon: the same die is binned, and for a stage that drives an actuator rather than measures a microvolt the AP grade is the sensible purchase. It becomes the wrong purchase only when the loop is closed around the high voltage output and the offset appears as a positioning error.

Supply rejection of 100 microvolts per volt maximum means a 10 V change on the high voltage rail appears as 1 millivolt at the input. In a high voltage amplifier that is driven from an unregulated rail, that 1 millivolt is multiplied by the closed loop gain and appears as an output error, so either the rail has to be regulated or the rejection has to be improved by a nested loop. This is the single most common reason a high voltage stage fails a noise test on the bench.

Where this order code fits

High voltage drive for piezoelectric actuators, electrostatic transducers, power supply error amplifiers, ATE pin drivers and any stage that has to swing 80 volts peak to peak uses this part. The JFET input keeps bias current negligible at room temperature, which matters when the feedback network is in the megohms. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

What is the maximum supply for the OPA445? Plus or minus 45 V, with the specified range starting at plus or minus 10 V. The input common mode then stops 5 V inside either rail, so the usable input window is 70 V at the full supply.

Why does the bias current rise so much over temperature? The input is a JFET pair, and junction leakage roughly doubles every 10 degrees. 50 picoamps at 25 C becomes 20 nanoamps over the specified range, which is 400 times larger and is the figure that sizes the feedback network.

Is the AP grade different silicon from the BM grade? No. It is the same die screened to a wider offset window and a different temperature range, which is why the price difference buys specification rather than performance.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.