Contact Us

ADS1231IDR

Brand: Texas Instruments
Texas Instruments ADS1231IDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS1231IDR — Power Management & Signal Chain | Superb Automation

ADS1231IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS1231IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS1231IDR: 24-bit bridge converter with a fixed gain of 128 and no registers

ADS1231IDR is the converter that a weigh scale uses when the firmware budget is a pin toggle in a SOIC body of 16 pins. The part is a complete front end for a bridge sensor: a gain of 128 amplifier, a third order 24-bit converter, an internal oscillator, an input filter and a low-side power switch that removes the bridge current between conversions. There are no registers to program, only two control pins and a two-wire serial output, and the supply range is 3 V to 5.3 V.

Order code and package

Order codeADS1231IDR
Function24-bit bridge converter, gain 128, oscillator and filter included
Input rangeplus or minus 19.5 mV full scale differential
Gainfixed at 128
Controlpin driven, no registers and no bus address
Outputtwo-wire serial, data ready on the same line
Referenceexternal, up to 5 V, for ratiometric bridge excitation
Data rate10 or 80 samples per second, selected by a pin
PackageSOIC, 16 pins, 9.90 mm by 3.91 mm
Temperature rangeminus 40 to plus 85 C
Supply3 to 5.3 V
DatasheetSBAS414 revision D

Electrical parameters that decide the application

Noise35 nanovolts RMS, which on a 39 mV span is 0.09 percent before averaging
Full scale inputplus or minus 19.5 mV, so a 2 mV per V bridge at 5 V excitation uses 10 mV of the 39 mV span
Low-side switchremoves the bridge current between conversions, which is where the self heating comes from
Referenceexternal and up to 5 V, so the bridge and the reference can share one excitation source
EMI filteron the analogue inputs, before the amplifier rather than after it
Data rate10 or 80 samples per second, a ratio of eight in noise terms
Supply currentset by the low-side switch duty cycle rather than by a register
Gain accuracyfixed at 128 with no gain calibration path inside the part
Interfacetwo wires plus a clock, so an isolated link needs only a digital isolator
Package thermalSOIC 16, 5.6 C per W junction to ambient on the exposed copper

Points to check before this part goes on a BOM

Nineteen and a half millivolts of full scale with a gain of 128 means the amplifier input sees the whole span, so a bridge with 2 mV per V sensitivity at 5 V excitation produces 10 mV and uses only half the converter range. That lost bit is bought back by raising the excitation, not by a software trick.

Thirty-five nanovolts RMS is the noise of the converter plus amplifier over the stated bandwidth, so the resolution is set by the bridge, not by the converter: a 350 ohm bridge at 5 V dissipates 71 mW and its own thermal noise is larger than the 19.5 mV span divided by the noise floor would suggest.

The reference is external and ratiometric by intent. Exciting the bridge and the reference from the same source cancels the excitation drift, which is the largest single error term in a scale that runs on a wall adapter.

The low-side switch turns the bridge off between readings. That is the feature that keeps a battery scale alive, but it also means the first conversion after wake-up is settling the bridge, so the host has to discard it or wait.

Ten and eighty samples per second differ by a factor of eight in rate and roughly a factor of three in noise once the digital filter is accounted for. A 10 SPS setting is a 100 ms window, which is also the mains rejection story on a 50 Hz supply.

There is no gain calibration register. The gain error of the internal amplifier is therefore a fixed term that has to be removed by a system-level calibration weight, which is normal for a scale but not for an instrument that has to read absolute millivolts.

Where this order code fits

('Boards that want a converter with a register map start from the 16-bit and 24-bit family pages instead.',) Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can the part be used for a 4-wire load cell? Yes, the four-wire bridge connects straight to the inputs, and the low-side switch can be used to remove excitation between readings.

Why is there no register interface? The part is built for a fixed-function scale: gain, filter and data rate are set by pins and by the external reference, so the firmware is a pin toggle and a shift in.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.